A hydraulic jump is shown in figure below. The depth of flow z₂ after the hydraulic jump is 5 m larger than z₁. The total flow rate in the channel is 450 m³/s and the channel width is 50 m. The length I over which the jump occurs is 0.4 m. ax Z1 IN V₁ €1 -0.133 If the depth, z₁, is 6 m then what is the average acceleration (ing's) of the liquid as is flows across the jump. Hydraulic jump g's V₂ 22

A hydraulic jump is shown in figure below. The depth of flow z₂ after the hydraulic jump is 5 m larger than z₁. The total flow rate in the channel is 450 m³/s and the channel width is 50 m. The length I over which the jump occurs is 0.4 m. ax Z1 IN V₁ €1 -0.133 If the depth, z₁, is 6 m then what is the average acceleration (ing's) of the liquid as is flows across the jump. Hydraulic jump g's V₂ 22

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The three reservoirs shown below are connected by commercial steel pipe (e=0.045mm.). Determine the flow rate in each pipe, assuming fully turbulent flow. Neglect minor losses. clev, 80 B 4000 m 1.2 m J (elev, 0) 8'09 000€ elev. 100 A ļ 5000 m 0.6 m elev. 70 C ļ
Onestion 2 : Choose the correct letter, A, B, C or D A 1 Esumate the flow velocity in m/s through a best hydraulic circular channel of 2 m diameter with a bed slope of 0.001 and n=0.012. 2 For a rectangular channel if the discharge per unit width= 10 m³/s.m, the critical velocity in m/s is? 3 For a rectangular channel if the flow velocity = 1.5 m/s, and the flow depth = 2m, what is the classification of this flow? 4 For a rectangular channel, if the Froude number = 1.5 and the initial depth=0.8 m, the depth after hydraulic jump occurs is: 5 At the exit flow under a sluice gate the depth of flow was 0.5 m, if y2=1.5 m, calculate the head loss across the jump 6 The pump curve of single pump is given by Hp = 15-100², if the system curve Hsu =20-20², estimate the flow delivered to the system by 3 pumps in series in m³/s 7 The pump curve of single pump is given by H₂=40-25Q², if the system curve HSH =20-20², estimate the flow delivered to the system by 3 pumps in parallel in m³/s What is…
1. The three reservoirs shown below are connected by commercial steel pipe (e=0.045mm.). Determine the flow rate in each pipe, assuming fully turbulent flow. Neglect minor losses. 므 clev. 80 B 4000 m 1.2 m J (elev. 0) w 8'09 000€ elev. 100 V A 5000 m 0.6 m elev. 70 7 C F
A hydraulic jump takes place in a rectangular channel downstream of a spillway. The flow in the channel is Q =900 cfs. The conjugate depth (y1) upstream of the jump was measured at 1.4 feet. The channel width is B = 15feet. (a) Compute the conjugate depth y2 downstream of the hydraulic jump.(b) What type of jump are we looking at in this problem? Refer to the five types presented (in the figureabove) by Prof. Ven Te Chow, the father of watershed hydraulics and physical hydrology.(c) Evaluate the specific energies E1 and E2 at points 1 and 2 (upstream and downstream of the jump,respectively) and the specific energy Ec corresponding to the critical depth yc. Then annotate thespecific energy diagram below with the values of y1, y2, yc, E1, E2, and Ec.(d) How much is the head loss in the hydraulic jump? Explain your answer.
Answer the following questions: In a supercritical flow, can a hydraulic jump be expected to be formed if the bed slope of the channel is sharply increased or reduced. Why or why not? Discuss the velocity distribution in the hydraulic jump. Draw the total energy and hydraulic gradient lines through a hydraulic jump. Give examples illustrating the practical usefulness of creating a hydraulic jump. Does the hydraulic jump have any application in the industry? Using illustrations, explain the practical use of creating a hump or a sudden drop in the bed of a channel. Explain why the forces acting on a jump over a sloping bed differ from those acting on a jump over a horizontal bed. Give two examples for hydraulic jumps formed over a steep bed.
There are three pipes and each has different friction or roughness factors below: Saint Pancras Pipe: C 120 %3D Leicester Pipe: n 0.02 Paddington Pipe: f= 0.03 The design headloss gradient is 4m for every kilometer. All pipes have diameter of 800mm and 700 meters long. Determine the discharge or flow rate in Liters per second on Paddington Pipe
A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13 m³.sec¹, velocity when the depth is one quarter of the diameter is 0.6 m.sec¹¹. Assume the flow is uniform and determine the diameter and the slope of the pipe if you know that Chezy's coefficient is 58 mº.5 sec¹? Answer// D= 460 mm; S= 0.00158
542..A hydraulic jump was established in the river. The depth before the jump measured 3.38 cm and the depth after the jump was 11.46 cm. The width of the river is 31.2 cm. Write the type of the jump when the discharge is 0.0162 m3/s.
There are three pipes and each has different friction or roughness factors below: Saint Pancras Pipe: C = 120 Leicester Pipe: n = 0.02 Paddington Pipe: f = 0.03 The design headloss gradient is 4m for every kilometer. All pipes have diameter of 800mm and 700 meters long. Determine the discharge or flow rate in Liters per second on Leicester Pipe
Q4 In the following figure shows a channel contraction section often called a venturi flume, because measurements of y, and y2 can be used to meter the flow rate. Show that if losses are neglected and the flow is one-dimensional and subcritical, Apply this to the special case b;=3 m, b;=2 m, and y,=1.9 m. a) Find the flow rate if y2=1.5 m. b) Also find the depth y2 for which the flow becomes critical in the throat. b, b2 Top view Side view
Determine the velocity of flow after hydraulic jump through a 1 m wide channel if the velocity of flow before jump was 2 m/s and the depth was 0.2 m.
2 When the pitot tube is moved vertically inside the pipeline, why does it yield different flow velocities? Explain 3~ If the pitot tube s not perfectly aligned with the current direction, it produces errors in the measurements of static pressure and total (pool) pressure, Why? Explain. 4~ When flow velocity increases, it alters the shape of the flow velocity profile. Clarify 5~ What are the advantages and disadvantages of the pitot static tube. 6 - Does altering fluid temperature influences the results obtained by pitot static tube? clarify