A humidifier in an air heating duct handles 3000 CFM, and increases the moisture content of the air from 30 to 60 g/lb a.s. Calculate the amount of heat needed for the humidifier, if the air is at 80°F.

A humidifier in an air heating duct handles 3000 CFM, and increases the moisture content of the air from 30 to 60 g/lb a.s. Calculate the amount of heat needed for the humidifier, if the air is at 80°F.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter46: Room Air Conditioners

Section: Chapter Questions

Problem 16RQ

See similar textbooks

Related questions

Q: Develop a plan to calibrate the following: (a) The standard National Weather Service rain gauge. (b)…

A: A rain gauge essentially gathers the water that falls on it and logs the change in rainfall depth…

Q: The net work output and the thermal efficiency for the Carnot and the simple ideal Rankine cycles…

A: Given data as per the question Condenser pressure =50 kpa Steam pressure at the entrance of turbine…

Q: 2. Compute the reactions at the pin B and at the roller A. A 30% 8 ft 800 lb ft -4 ft- B 390 lb 13…

Q: unting for stress concentrations. calculate the safety factor for the material selected. if matrial…

A: Given-Information:- Material 4150 AnnealdF1 = 9 kNF2 = 13 kNF3 = 15 kN To-Determine:- Safety Factor…

Q: 1. -5 m- 20 kN/m B -10 m

Q: It is known that the velocity distribution for steady, laminar flow in circular tubes (either…

Q: 13.12 Fluid A is found to have a surface tension of 0.080 N m−1, a density of 1.2 × 103 kg m−3 and a…

A: Given:Surface tension of fluid A, σA=0.080 N/mDensity of fluid A, ρA=1.2*103 kg/m3Contact angle for…

Q: For some given binary phase diagram, describe how you would: find the temperatures and compositions…

A: Given: For a binary phase diagram To find: Temperatures and compositions of all eutectic,…

Q: The assembly in figure 1 is rotating counterclockwise from above at w = 10 rad/s about the z axis.…

A: Given: To find: Inertia tensor about CD axis Moment of inertia of rod about z axis Angular…

Q: = Consider a plane wall 100 mm thick and of thermal conductivity 120 W/m-K. Steady-state conditions…

A: Heat flux flowing in the material is defined as total heat transferred in the material per unit…

Q: What are the best dimensions for a rectangular brick channel (n = 0.015) designed to carry 5 m³/s of…

A: Given data as per the question Flow rate=5 m3sn=0.015S0=0.001

Q: A frictionless piston-cylinder device contains a saturated liquid-vapor mixture of water at 400K.…

A: Twater = 400 K Tsurr = 300 K Q = -960 kJ ('-' indicates heat rejected by system) dS = ?

Q: A a= -0.5 m Submit 15 kN 195| ΑΣΦ | | Determine the minimum dimension a to the nearest mm of the…

Q: n the two-pipe system, water flows continuously from the inner pipe and air from the outer pipe…

A: Given Data: m˙1 = 10 kg/sm˙3=5 kg/sT3 = 1200 KT4=T2P1=1 bar and Saturated water vapor Find:…

Q: Disk A weighs 4.00 lb and Disk B weighs 1.00 lb. Disk A is driven by a 30.0 in-lb torque as shown.…

A: To find: The angular acceleration of disc B. Given: The mass of disc A, mA = 4 lb. The mass of disc…

Q: Consider the mixing chamber shown in the figure below. In the device, 2.2 kg/s ammonia at 1000 kPa,…

A: (a) To find: The vollume flow rate of the second flow. Given: The pressure at the inlet 1 is P1=1000…

Q: QUESTION 4 Analyze the truss and calculate all the forces acting on Joint B and H. Show your detail…

Q: A hollow aluminum shaft, G=27GPa, douter-96mm, dinner= 52mm has an angle of twist per unit length of…

Q: PROBLEM F8-13 A 100 mm long rod has a diameter of 15 mm. If an axial tensile load of 10 kN is…

Q: A -L/2- (x = 0, y = 0) (x=L, y=0) (x=0,² = 0) C -L/2 B

Q: Problem 1 100°C. - 10 kg of water is contained in a rigid 1 m³ container. It is heated from 20°C to…

Q: A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing…

A: given : d₀ = 250 mm ∴ r₀ = 125 mm dᵢ = 150 mm ∴ rᵢ = 75 mm P = 18.75 kW @ 500 rpm μ = 0.3 number of…

Q: An oil heater heats 60 kg per minute of oil from 28°C to 70°C in a counter-flow heat exchanger. The…

Q: Which of the following is NOT an impact of IP infringement? O Loss of sale Loss of market share…

A: Due to intellectual property (IP) infringement, there is loss of market share because same products…

Q: n the figure, the slender bar (1), with a mass of 30 kg, is attached to the sphere (2), with a mass…

A: Given Data: m1=10 kgm2=5 kgR = 200 mm=0.2 mω = 1.2 rad/sθ = 30oL = 800 mm=0.8 m Find: a. The angular…

Q: The section of shaft shown in the figure is to be designed to approximate relative sizes of D=1.5d,…

Q: Determine the maximum force P that can be applied without causing the two 50-kg crates to move. The…

A: Introduction Using the equilibrium equation, we will compute the greatest force that can be applied…

Q: Required information A Diesel cycle has a compression ratio of 22 and begins its compression at 87…

Q: Two plates are clamped by a 3/4-10 UNC SAE Grade 5 bolt and regular nut with a 3/4-W plain washer as…

Q: End A of the 8-kg uniform rod AB is attached to a collar that can slide without friction on a…

A: To find: The angular acceleration of the rod and the reaction at A. Given: The length of the rod, l…

Q: The rotation axis of the uniform cylinder is constrained by a frictionless slot. The cylinder is at…

A: Given data: Belt translational velocity V = 20 ft/s Coefficient of friction μ=0.4 Find: a) Calculate…

Q: Determine the reactions to the structure w2 = 200 lb/ft w1 = 100 lb/ft 15 ft 4000 lb 5 ft

Q: 7.6. Derive an expression for pipeline Reynolds number in terms of Q, d, and v.

Q: Design a 02-series angular contact ball bearing to support a radial load of 12kN and axial load c…

A: This question is of Machine design Subject.

Q: A flat belt with a width of 120 mm and a thickness of 5 mm transmits power from a driving pulley…

Q: The disk with radius r is rolling (without slipping) with angular velocity through the bottom of the…

A: Given Disk is rolling without slipping angular velocity of the disk (ω) = 2rad/sec radius of the…

Q: Thermo plastic polymers fatigue tested at frequencies above 1Hz display; Excellent resistance to…

A: Thermoplastic polymers: These are polymers with high molecular weight. They are made up of plastic…

Q: The Kelvin-Planck and Clausius statements of thermodynamics are equivalent. In order to prove the…

Q: 3–15. A utility lift vehicle is shown in Figure P13.15. Determine the force required by the…

A: Given data as per the question Load on the lift vehicle =1200 N

Q: How would you solve this manually without an equation solver

Q: An oil heater heats 60 kg per minute of oil from 28°C to 70°C in a counter-flow heat exchanger. The…

A: Given: m˙c=60kg/min=1kg/s Tc,i=28oC Tc,o=70oC Cc=2.5 KJ/KgoC Ch=1 KJ/KgoC m˙h=100kg/min Th,i=200oC…

Q: 1 W L-1 recee Fi

A: Given system,

Q: 3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid…

A: Density of water =1000 kg/m3 Density of mercury = 13500 kg/m3 Density of Glycerine = 1260 kg/m3…

Q: Figure 1 is a schematic drawing of a countershaft that supports two V-belt pulleys. For each pulley,…

A: Given data, For pulley A Tension in tight side, T1 = 103 N Tension in loose side, T2 = 0.15T1…

Q: Air is compressed in a compressor through the purely polytropic, purely isothermal, and intercooling…

A: The intercooling process is 1-X-X'-2 Answer: B. 1-X-X'-2

Q: eaner units. After delivery, the hote mits should have been tested to mee m IEC 60312, a European…

A: Given-Information:- The United States does a contract with a European vacuum cleaner company. ASTM…

Q: You are given 1) the normal to the slip plane and the normal to the slip direction angle with the…

Q: A plane wall of length L = 0.4 m and a thermal conductivity k = 1W/m-K has a temperature…

A: Introduction Convective heat transfer, conductive heat transfer, and radiative heat transfer are the…

Q: Liquid fuel of kinematic viscosity 2.37x10-6 flows through the pipe of diameter 15 cm. Determine the…

Q: A large wood products company is negotiating a contract to sell plywood overseas. The fixed cost…

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

mo A humidifier in an air heating duct handles 3000 CFM, and increases the moisture content of the air from 30 to 60 g/lb a.s. Calculate the amount of heat needed for the humidifier, if the air is at 80°F.
what is the heating value of oil in BTU/lbm at 27 degree API
Pls. Answer thank you! The moisture removed from a material is 200 lb/hr and change of humidity ratio in dryer is 0.015. Determine the fan capacity if specific volume of air entering is 38 ft3/lb.
Compare the diffence in number of gallons used to heat a home with natural gas compared to oil under the same conditions. Which one is cheaper to use?
1. A cylindrical tank, 3 m long and 2 m in diameter is used for oil storage. How many days can the tank supply the engine having 27°API with fuel consumption of 60 kg/hr if the average tank temperature is 24°C?
The evaporator design temperature may in some cases operate at a slightly ____(higher or lower) pressure and temperature on high-efficiency equipment because the evaporator is larger.
Pls. Answer thank you! Water at 55°C is cooled in a cooling tower which has an efficiency of 65%. The temperature of the surrounding air is 32°C dry bulb and 70% relative humidity. The heat dissipated from the condenser is 2,300,000 KJ/hr. Find the capacity in liters per second of the pump used in the cooling water
The return air temperature of the room is 78F and cooling system load is 48,000 Btu h (sensible). How much air flow (in CFM) is required for proving 58F as the supply air temperature?
What comes up next to the Heat value of natural gas? Q is what? Also, in Fuel Oil, where does the heat required come from?
Q1: Steum at a pressure of 28kpa is passed into a condenser and it leawes as condensate at a temperature of sac Cooling water circulates through the condenser at the rate of 45 kg/min - It enters at 152 and Veaves at 3oc If the Steam flow rate is 1.25 eg/min, determinė the drynes fraction of Steam as it enters the condenser.
4. A water tube boiler has a heating surface area of 500 m². For a developed boiler hp of 825. Determine the percent rating of the boiler. The percent rating of water tube boiler is 200%, factor of evaporation of 1.08 and heating surface area is 256 m?. Find the rate of evaporation. 5.
Air at a dry ball temperature of 90 danC and 4% RH is passed over the cooling coil so that the air dry bulb temperature becomes 45˚C. how much heat is released from the air in the process? = (Kj / kg)