A hollow aluminum circular cylinder, 32 cm tall with 5.0 cm outside diameter and a wall thickness of 0.35 cm, is used to support a compressive load L applied along the axis of the cylinder. Determine the maximum allowable value of L if the compressive stress is limited to 65 MPa and the deformation is limited to 0.044 cm.

A hollow aluminum circular cylinder, 32 cm tall with 5.0 cm outside diameter and a wall thickness of 0.35 cm, is used to support a compressive load L applied along the axis of the cylinder. Determine the maximum allowable value of L if the compressive stress is limited to 65 MPa and the deformation is limited to 0.044 cm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

A thin cylinder of inner radius 500mm and thickness 10mm is subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
A thin circular disk of inner radius a and outer radius b is shrunk onto a rigid plug of radius a + 8o. Determine (a) the interface pressure and (b) the radial and tangential stresses. a+ 8o Rigid core Disk
The state of stress at a point under plane stress 40 MPa, Oyy condition is Ox = = 100 MPa and Txy 40 MPa. This radius the Mohr's circle representing the given state of stress in MPa is:
Question 5 A same circular plate with radius of Ro-560mm and thickness of h=7.42mm is considered here again. The plate is subjected to a pressure of P-2,600 KPa and the Poisson's ratio is V-0.32. Find the absolute value of the radial stress at the centre of the plate in KPa (write your answer without considering the negative or positive sign). (Hint: round your answer 4 digits after decimal point))? Ro Your Answer: Answer
(1) A steel cylinder (Øyp = 260 MPa) of inner radius a and outer radius 3a is subjected to an internal fluid pressure pi (Note: ratio of wall thickness (t) to inner radius indicates that this is a thick-walled cylinder). (a) Determine (i) the maximum radial stress (ơmax); (ii) the maximum tangential stress (o0max). (b) Determine the limiting values of p, using: (i) the maximum distortion energy theory of failure; and (ii) the maximum shear stress theory of failure. (Hint: Maximum radial and tangential stresses occur at the same radial distance, see slide 8 of Lecture 9 notes); use these maximum stresses as your principal stresses). (c) A steel gun barrel of inner radius 0.6 m is subjected to an internal explosive pressure of 80 MPa. The tensile and compressive elastic strengths of the material are 320 MPa. Assuming a factor of safety of 2, design the wall thickness of the gun barrel.
Consider the plane stress element shown in representing the state of stress at a material point. If the magnitudes of the stresses are such that ox 210 Pa, oy = 110 Pa, and = - Txy = 70 Pa, calculate the magnitudes of principal stresses oj and 02, and the maximum shear stress, Tmax, generated at %3D this material point. (a) Record here the the positive of the two principle stresses. (b) Record here the the negative of the two principle stresses. (c) Record here the the maximum shear stress. Tyz Oy
A Cantilerer ród is loades as shown in the frguirel, If the tenste yield strength Of the mooteriel is 300Mpa, the diameter of the rod using O. Maximum piempal principal stress theory 6. Maximum sheur stress theory O. Maximum destortron enerey theory. determine -120mam ALB キ=2N P- lokN
a) A cylinder with a 0.30-m inner diameter and a 0.40-mouter diameter is internally pressurized to 100 MPa. Determinethe maximum shear stress at the outer surfaceof the cylinder. b) A thin-walled cylinder containing pressurized gas isfixed by its two ends between rigid walls. Obtain anexpression for the wall reactions in terms of cylinderlength l, thickness th, radius r, and internal pressure pi.
Solve two problems on statically indeterminate structures(strain energy method), two on thin wall pressure vessels(1-sphere and 2-cylinder), and one on thick wall cylinder, given below. A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa, determine the radial and tangential stress. Determine the maximum shear stress in the cylinder. Assume it has closed ends.
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
A Cantilever ródis loades as ghown in the figuirel, If the tensle yiels strength f the materrel is 300Mpa, the diameter of the rod using O. Maximum gerieimpal principal stress theory 6. tMaximem sheur stress theory Maximum destortion energy theory- determine 120mm A1
A thick cylinder of 150 mm outside radius and 100 mm inside radius is subjected to an external pressure of 30 MPa and internal pressure of 60 MPa. Calculate the maximum shear stress in the material of the cylinder at the inner radius