Consider a 60-mm cube made of graphite-reinforced polymer composite material that is subjected to a tensile force of 100 kN perpendicular to the fiber direction, directed along the 2-direction. The cube is free to expand or contract. Determine the strains (ɛ11, E22, E33, Y23, Y31, Y12) using following material constants for graphite-reinforced polymer composite. E1 = 155 GPa, E2 = E3 =12.10GPa U 23 = 0.458, D12 =D13 = 0.248 G23 = 3.20GPA, G12 = G13 = 4.40 GPa

Consider a 60-mm cube made of graphite-reinforced polymer composite material that is subjected to a tensile force of 100 kN perpendicular to the fiber direction, directed along the 2-direction. The cube is free to expand or contract. Determine the strains (ɛ11, E22, E33, Y23, Y31, Y12) using following material constants for graphite-reinforced polymer composite. E1 = 155 GPa, E2 = E3 =12.10GPa U 23 = 0.458, D12 =D13 = 0.248 G23 = 3.20GPA, G12 = G13 = 4.40 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A new rigid biomaterial is developed and tested as a candidate replacement tissue for volumetric loss of bone. To evaluate biomechanics, the biomaterial is stretched in the vertical direction in an unconfined configuration. However, you are unsure whether the biomaterial shows isotropic or anisotropic material properties. Write expressions for normal strains €11, 22, and 833 for orthotropic material symmetry. Next, write expressions also for normal strains E11, E22, and E33 for isotropy, stating your assumptions that allow you to simplify the moduli of elasticity and Poisson's ratios. To evaluate the importance of anisotropy, you decide to evaluate error in 833 measured in the orthotropic case, compared against the isotropic case. If we know that Poisson's ratios for anisotropy change by 5%, i.e., U12 =U21= U13 = U31 = U23 = U32 = 1.05 u, determine further how E33 changes. Comment on whether the change in E33 is below 10%, considered "acceptable". For an incompressible, isotropic…
Compare the strain energies of two bars of the same material and length and carrying the same gradually applied compressive load if one is 25 mm diameter throughout and the other is turned down to 20 mm diameter over half its length, the remainder being 25 mm diameter. If both bars are subjected to pure torsion only, compare the tensional strain energies stored if the shear stress in both bars is limited to 75 MN/m2
O 0.6% 19% If an isotropic material has a Young's modulus of 85 Gpa and a Poisson's ratio of 0.25, calculate its shear modulus. Select one: O G = 29 Gpa O G = 34 Gpa G = 25 Gpa O G= 77 Gpa O G= 46 Gpa If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal BD. C 2 mm 4 mm EN DO O
A sample of cross-linked natural rubber (polyisoprene) is found to have a shear modulus of 100 kPa at 20˚C. Determine the force needed to stretch a 20 mm diameter by 100 mm long rod to 300 mm (stretched in the length direction). What is the diameter of this rod of natural rubber under such a load?
question 1 of 3 A1 meter length of rubber with a Young's modulus of 0.01 GPa, a circular cross-section, and a radius of 0.001 m is subjected to a force of 1,000 N. What is the new length of the rubber after the force is applied (assuming it doesn't break)? O 10.5 m O 32.8 m O 31.8 m O 1.83 m
A thin plate is subjected to a biaxial stress field of  x= 1 Gpa and  y= 0.5 Gpa. Calculate the strains in the xy directions if the plate is made of (a) steel, (b) a 0° unidirectional boron-epoxy composite. For the boron-epoxy composite use the following properties: Young’s Modulus at 0°=207 Gpa, modulus at 90° = 19 Gpa,  12=0.21, G12= 6.4 Gpa. Assume for steel a young’s modulus = 207 GPa
A copper cylinder with a length of 1.5 m and diameter of 4 cm undergoes compression. Bulk Modulus (14*10^10 Pa) What will be the bulk strain of the copper rod if pressure is applied to reduce its volume to 0.00089 m3? How much pressure was applied to the copper rod? Calculate the percent change in volume of the copper rod.
An elastoplastic material with strain hardening has the stress–strain relationshipshown in Figure 1.6(c). The modulus of elasticity is 175 GPa, yield strength is480 MPa, and the slope of the strain-hardening portion of the stress–strain diagramis 20.7 GPa.a. Calculate the strain that corresponds to a stress of 550 MPa.b. If the 550-MPa stress is removed, calculate the permanent strain.
A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is limited to 0.1% and density of 7800kg/m^3, what is the maximum internal diameter of the tube in mm?
! How to compute the strain displacement matrix for each element?
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a compressive load of 3 kN is applied parallel to the 2.3m dimension, what is the resulting engineering normal strain?
5. Please calculate the strain and stress in the following two prompts a. A 1 cm long section of tendon stretches to 1.011 cm when it is subjected to a tensile force of 40,000 N. What is the strain in this segment of tendon? @? 17 b. The section of the patellar ligament in the previous question is 0.02 m² in the cross section. What is the stress in this section of ligament as a result of 50,000 N tensile force? E = Δι 19 0 = A 1.011 cm 50000 0,02 Scoco 40000 1.25 = T % 2500000 strain N/m² on trito flox your wrist, you may notice that your