A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T" developed is ___KN-m A 5.03 B) 3.82 C) 2.64 D) 1.18 E) 0.48

A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T" developed is ___KN-m A 5.03 B) 3.82 C) 2.64 D) 1.18 E) 0.48

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The moment of inertia of the profile below in relation to Y is valid. Make the calculation memo of the question:
2) The extension spring shown in figure has full-twisted loop ends. The material is BS 5216 Grade 2. The spring has 84 coils and is close-wound with a preload Inside dia. 50 mm of 80 N. a) Find the closed length of the spring. b) Find the torsional stress in the spring corresponding to the preload. 5 mm c) Estimate spring rate. 5 mm d) What load would cause permanent deformation? e) What is the spring deflection corresponding to the load found in part Running length= 100 mm Assembled length= 180 mm Free length= 200 mm
Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure , Determine the angle of rotation at the free end. D2 D1 T (kN-m) Given: L(m) T(KN-m) D1 (mm) 02 (mm) G (GPa) 28 60 140 120
Solve for c) only
solve 30-40 minutes hand written asap..i'll rate
Draw bending moment diagram for the loading shown in Figure Q15
2) The extension spring shown in figure has full-twisted loop ends. The material is BS 5216 Grade 2. The spring has 84 coils and is close-wound with a preload of 80 N. 6 mm a) Find the closed length of the spring. 40 mm b) Find the torsional stress in the spring corresponding to the preload. 18 mm 10 mm c) Estimate spring rate. d) What load would cause permanent deformation? e) What is the spring deflection corresponding to the load found in part
Two solid circular shafts are connected through a flange bolt coupling consisting of 3 circular bolt rows. The free ends of the shafts are to be subjected by equal torque. Solid Shafts Diameter (mm) Length (m) Shear Modulus (GPa) Shaft A Shaft B 65 66 3 3.8 81 84.6 Flange-bolt coupling Bolt Circle Diameter (mm) Bolt Alowable Shear Stress (MPa) Bolt Diameter Shear Modulus Number of Bolt Row (mm) (GPa) Bolts 1 95 14 77 35 4 2 116 17 97 42 10 3 135 13 93 49 14 A Calculate the torque capacity of the flange-bolt coupling (kN-m). B. Calculate the stresses in both shaft if the torque capacity is applied at both ends (MPa). C. Calculate the total angle of twist (in degrees).
A stainless steel beam with a diameter of 5cm is completely fixed at one end and is subjected to a uniformly distributed torque a) Calculate the reactions at the support b) Draw the torque diagram for the entire beam Clearly indicate the equations used for each section c) Calculate the absolute maximum shear stress in the bar. Clearly indicate its location d) Calculate the angle of twist of the free end with respect to the fixed end. Arixed 0.5m 200NM/M 0.5m 0.5m
machine design