A hole of are 2 mm^2 opens in the pipe near the lower end of a large water-storage tank, and stream of water shoots from it. If the top of the water in the tank is 20m above the point of the leak, how much water escapes in 2 seconds? (L)

A hole of are 2 mm^2 opens in the pipe near the lower end of a large water-storage tank, and stream of water shoots from it. If the top of the water in the tank is 20m above the point of the leak, how much water escapes in 2 seconds? (L)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q2) ) A piping system consists of three pipes arranged in series the lengths of the pipes are…

Q: What is the velocity of the pipe center (m/s)? Given that h3=31.3 cm hy =7 am h= 3 cm Water

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: Water flows through a pipe at 130 L/s that changes gradually in diameter from 154mm at point A to…

Q: Water is delivered through a horizontal 20-cm-diameter pipe at a flow rate of 0.5 m3/s. If a…

A: Answer: The pitot probe positioned downstream of the manometer would indicate a pressure of 176.65…

Q: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type mercury…

A: we have to judge the use of these manometers in this experiment

Q: A venture-meter is shown in Figure (1) carries water, find the flow rate if there are no losses…

Q: he air is measured at 20 deg. C and 679mm Hg. The duct diameter is 744 mm while the discharge…

A: Given, Air temperature , T =20 deg C Pressure - P1 = 679 mm hg volume flow rate , Q = 4m3/s.…

Q: A 45° reducing bend in a horizontal plane, 0.59 m diameter upstream and 0.23 m diameter downstream…

A: The given values are - Q =0.46 m3/sd1=0.59 m , d2=0.23 mP1 =1.46 bar =146 kPa Assuming that the…

Q: 1) A plugged dishwasher sink with the dimensions of 16 in. ✕ 20 in. ✕ 7 in. is being filled with…

A: As per our company guidelines, we are allowed to answer only the first question in case of multiple…

Q: 4.Oil with specific gravity 0.750 is flowing through a 6-in pipe under a pressure of 15.0 psi. If…

A: The given information in the problem is shown in the following attached image:

Q: Eight cubic feet of water flow per second downward through this pipe line. When the upper pressure…

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: Guava juice enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft3 / hr, then exits through a…

Q: Water with a velocity of 7.06 m/s flows through a 73 mm diameter pipe. Solve for the mass flow rate…

Q: 3. Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154 mm) at…

A: Water flows through a schedule-40 pipe that changes gradually in diameter from d1= 6 in (0.154 m) at…

Q: Question 3 Water flows steadily through the variable area pipe as shown. a) Determine the velocities…

Q: Water is delivered through a horizontal 20-cm-diameter pipe at a flow rate of 0.5 m3/s. If a…

Q: Determine minor and major losses.

A: Given: Discharge= 6 l/s TO determine: Major and minor losses

Q: 5. Write down the Benoulli equation and explain the meaning of each terins 6. Water is flowing…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: The water is flowing through a pipe having diameters 40 cm and 17 cm at sections 1 and 2…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: What is the velocity of the pipe center (m/s)? Given that h3%-88.3 cm h3 h2 =7 cm h =3 cm] Water

A: hps=88.3+7hps=95.3 cm or 0.953 mhp=7 cm or 0.07 m apply bernoulli's equation between 1 and…

Q: re. The ocities are

A: given:

Q: If the velocity of a liquid is 1.65 ft/s in a 12-inch diameter pipe What is the speed of a 3-inch…

A: The initial velocity v1=1.65 ft/s The initial diameter d1=12 in The final diameter d2=3 in

Q: Q1: An Orifice meter is inserted in a pipe of 20 cm diameter. Water flows through the pipe and the…

Q: A syringe is used to deliver vaccine against an infectious disease. This particular syringe is not…

A: Given: Leaked flow rate is 5% past the plunger. Flow rate of the vaccine is 270 cm3/min. Velocity of…

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A: Given: The flow rate, Q = 400 gal/min The pipe type = schedule 40

Q: The water is flowing through a pipe having diameters 30 cm and 21 cm at sections 1and 2…

Q: Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the…

A: When any fluid having velocity V passes through a pipe of area A, then discharge through the pipe is…

Q: Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the…

A: When any fluid having velocity V passes through a pipe of area A, then discharge through the pipe is…

Q: Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of…

Q: ... P1 = 50 KPa %3D P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the…

A: To obtain the discharge of water through the orifice, we must apply the Bernoulli's equation between…

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

Q: using 2 L please solve it in these steps step 1- find velocity of the fluir using bernoullis…

A: Step 1:Step 2: Step 3: Step 4:

Q: The water in a 750 cubic meter treatment water tank is discharged under the influence of gravity to…

Q: Water is delivered through a horizontal 20-cm-diameter pipe at a flow rate of 0.5 m3/s. If a…

A: Given data:

Q: Oil (density = 842 kg/m³ and kinematic viscosity = 6.2e - 4 m²/s) is being discharged by a 66 mm…

A: Given:Oil density, ρ=842 kg/m3Kinematic viscosity, ν=6.2×10-4 m2/sPipe diameter, d=66 mm=0.066…

Q: A pumping station wet well operates between 540- and 550-ft elevation. The pump curve is deϐined by…

Q: FOR THE PIPE NETWORKS SHOWN, THE FLOW OF WATER FROM A TO THE FIRST JUNCTION IS 2 CUBIC FEET PER…

A: given that , Q1=2 Av1=2 3.14✕0.335✕0.335✕v1=2 v1=2/0.35 =5.71ft/s Head loss is express by Darcy…

Q: . A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and…

A: Here given data says that Hight ,= 30 m Diameter at bottom= 6 m Diameter at top = 4.5 m Wight of…

Q: Please try to answer in text Water flows through 100 mm diameter pipe from A to B. The velocity is…

A: Hydraulic grade line is defined as piezometer head.

Question

0.0792

0.789

7.954

0.00736

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Question 3 Water flows steadily through the variable area pipe as shown. a) Determine the velocities in the large diameter pipe (12 cm) and the small diameter pipe (8 cm). b) Determine the discharge. Open Open Oil S = 0.7 1.5 m 12 cm 2 m 8 cm-
A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e-0.026mm, v1.13" 10 m?/sec). Fig(1) 6m 23m Fig.(1) Nozzle
Q1: A water tower is an elevated structure supporting a water tank constructed at a height sufficient to pressurize a distribution system for potable water. A completely filled and pressurized water tank was found with a small leakage (a hole 5cm in diameter) located on the sidewall of the tank, around 5 meters below the top of the tank. Please calculate the velocity of leakage water that discharges to the normal atmosphere. The dimension of the tank is 20-meter in height and 10-meter in diameter. The gauge pressure of the water tank top is 0.1M Pa. The Bernoulli equation is: P₁/pg + V₁²/2g +h₁ = P₂/pg + V₂²/2g +h₂ Gauge Pressure: 0.1 M Pa 5 meters Leakage velocity?
Water with a velocity of 7.83 m/s flows through a 126 mm diameter pipe. Solve for the mass flow rate in kg/s. Express your answer in 2 decimal places.
Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of the inverted tube is 1 meter above the free surface of the alcohol in the tank and 10.5 meters above the ground where the alcohol is discharged. Alcohol exits the tube at atmospheric pressure. The Specific gravity of alcohol is 0.89 while g= 9.81. The pressure, in kilopascal, in the bend is Blank 1 P=? 1m
Q2) Oil flows through a pipe as shown in fig2. The coefficient of discharge for the orifice in the pipe is C.-0,63. What is the discharge of oil in the pipe? P1-P2 P1-P2 V22-V₁² Let: -4.48. Y 100-mm-diameter, sharp-edged orifice (2) 250mm 6.958 Heavy oil
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
Solve the following fluid mechanics questions
Orifice Given:As = 3m2C = 0.92Ao = 0.01m2 Determine the time for the depth of liquid in the tank to be 0.8m
The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m° and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. 0.409 MPa 0.125 MPa a. The energy added in meters and the power delivered in kilowatts to the water by the pump. b. The mechanical efficiency of the pump. P 0.04meter Ø 0.1meter Ø
The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and smaller ends are located 8 meters and 4 meters, respectively, from a datum line. If at the larger end the velocity is 1.2 meters pee second and the pressure is 5300 kN/m^2, compute the pressure at the smaller end