a heat exchanger, water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150 degree celsius on the outside of the tube. Water enters at 15 degree Celsius and leaves at 60 degree Celsius . What is the heat transfer coefficient, h, for the water? Write the given, required and solution

a heat exchanger, water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150 degree celsius on the outside of the tube. Water enters at 15 degree Celsius and leaves at 60 degree Celsius . What is the heat transfer coefficient, h, for the water? Write the given, required and solution

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.43P

See similar textbooks

Similar questions

Mot water is used to heat air in a double-pipe heat exchanger as shown in the following sketch. If the heat transfer coefficients on the water side and on the air side are 550W/m2Kand55W/m2K respectively, calculate the overall heat transfer coefficient based on the outer diameter. The heat exchanger pipe is 5-cm, schedule 40 steel (k=54W/mK) with water inside.
Water flowing in a long, aluminum lube is to be heated by air flowing perpendicular to the exterior of the tube. The ID of the tube is 1.85 cm, and its OD is 2.3 cm. The mass flow rate of the water through the tube is 0.65kg/s, and the temperature of the water in the lube averages 30C. The free-stream velocity and ambient temperature of the air are 10m/sand120C, respectively. Estimate the overall heat transfer coefficient for the heat exchanger using appropriate correlations from previous chapters. State all your assumptions.
10.1 In a heat exchanger, as shown in the accompanying figure, air flows over brass tubes of 1.8-cm 1D and 2.1-cm OD containing steam. The convection heat transfer coefficients on the air and steam sides of the tubes are , respectively. Calculate the overall heal transfer coefficient for the heal exchanger (a) based on the inner tube area and (b) based on the outer tube area.
PLEASE ANSWER ASAP In a heat exchanger, water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150 degree celsius on the outside of the tube. Water enters at 15 degree Celsius and leaves at 60 degree Celsius . What is the heat transfer coefficient, h, for the water? Write the given, required and solution
1) For a concentric counter-flow heat exchanger, hot oil is coming in the tube of the shell/tube heat exchanger and it's cooled by water that surrounds it in the shell. Calculate what is the required length of the heat exchanger tube in order to perform the necessary cooling. Assume there is negligible heat loss to the surroundings and negligible conductive heat resistance between the two fluids. Mass flow rate of oil = 0.17 kg/s Oil heat capacity = 2375 J/kg-ºC Oil convective heat transfer coefficient = 39.7 W/m²-°C Oil enters tube at temperature = 130 °C Oil leaves tube at temperature = 83 °C Water convective heat transfer coefficient = 2190 W/m²-°C Water enters shell at temperature 15 °C Water leaves shell at temperature = 74 °C Inner diameter = 4.5 cm Outer diameter = 6.5 cm
QUESTION & A concentric-tube, counter-flow heat exchanger, as shown below, is used to cool mercury [C. h= 1,370 J/kg · "C] flowing at a rate of 1.0 kg/s from 110°C to 70°C. The cooling fluid is water entering the heat exchanger at a temperature of 30°C and flow rate of 0.2 kg/s. The overall heat transfer coefficient of the exchanger is U = 250 W/m. °C. Water Mercury Determine the outlet temperature of the water. O None of these answers O 95°C O 125°C O 105°C O 85°C
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following: (a) Calculate i) methanol mass flow rate in the exchanger, ii) methanol volumetric flowrate at the inlet of the exchanger. (b) i) For the counter-current flow of the fluids calculate the log temperature difference, ii) explain the purpose of calculating this difference, iii) explain, quantitatively, why is the counter-current flow in heat exchangers preferred to co-current flow. mean
3.21 You must cool 78 kg/min of a 60%-by-mass mixture of glycerin in wa- ter from 108°C to 50°C using cooling water available at 7°C. Design a one-shell-pass, two-tube-pass heat exchanger if U = 637 W/m²K. Which side should the water flow through? Explain any design decision you make and report the area, TH₂0out and any other relevant features.
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s-1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following:
QUESTION 3 A multi-stage steam turbine exhausts into a two-pass surface condenser operating at a pressure of 10kPa. The steam enters the condenser with a dryness fraction of 0.85 and the condensate leaves the condenser at a temperature of 34.6°C. The tubes have an inside diameter of 18mm and a wall thickness of 1mm. Coolina water circulates through the tubes at a speed of 1.2m/s. The stean flows through the condenser at a rate of 2400kg/hr and air leaks into the system at a rate of 0.5kg/1000kg of steam condensed. Calculate: 3.1 the capacity of the air pump in m2/min.
Shell-and-tube heat exchangers with hundreds of tubes housed in a shell are commonly used in practice for heat transfer between two fluids (shown in Figure 1). Such a heat exchanger used in an active solar hot-water system transfers heat from a water-antifreeze solution flowing through the shell and the solar collector to fresh water flowing through the tubes at an average temperature of 60°C at a rate of 15 L/s. The heat exchanger contains 80 brass tubes 1 cm in inner diameter and 1.5 m in length. Disregarding inlet, exit, and header losses. (a) Determine the pressure drop across a single tube and the pumping power required by the tube- side fluid of the heat exchanger. After operating a long time, 1-mm-thick scale builds up on the inner surfaces with an equivalent roughness of 0.4 mm. For the same pumping power input, (b) Determine the percent reduction in the flow rate of water through the tubes. 80 tubes 1.5 m I cm Water Figure 1. Shell and Tube heat exchanger
1- For the following design conditions:- Condenser heat load (Qc) = 293 MW Condenser Pressure (Pcond) = 0.06 bar Cooling Water inlet temperature (tw,) = 25 C° Cooling Water velocity (Vw) = 2 m/s Number of Passes (N) = Single Tube Diameter (D) Tube Length (L) = 15 m Tubes Cleanliness factor (Fclean) = 0.85 Overall heat transfer coefficient (U,) = 4000 W /m²C°. Calculate the following:- = 25 mm a. Condenser Surface area b. Cooling water mass flow rate c. Condenser effectiveness