A given circuit has a resistor (R=20 ohms) and an inductor (L=0.3 henrys) connected in series with asinusoidal voltage with the following equation:v(t) = 120v2cos (120t + 10°)a.) Find the current immediately after switchingb.) Find the magnitude of impedance (in ohms)c.) Find the steady-state RMS current in amperes

Answered: Image /qna-images/answer/d34f606c-b0e4-4626-a51b-0b94e3e8f3c4.jpg

A given circuit has a resistor (R=20 ohms) and an inductor (L=0.3 henrys) connected in series sinusoidal voltage with the following equation: v(t) = 120v2cos (120nt + 10°) a.) Find the current immediately after switching b.) Find the magnitude of impedance (in ohms)

A given circuit has a resistor (R=20 ohms) and an inductor (L=0.3 henrys) connected in series sinusoidal voltage with the following equation: v(t) = 120v2cos (120nt + 10°) a.) Find the current immediately after switching b.) Find the magnitude of impedance (in ohms)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Related questions

Q: Q2: For the circuit in the figure, find: 16mH 265µF R = 40 + UL - 70.7 sin 377 a) Find the current I…

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is applied to the circuit…

Q: Q Find the capacitance C necessary to improve the power factor to 0.95 lagging in the circuit shown…

A: Z = 20∠30°Z = 20(Cos 30°+j Sin 30°)Z = 20 32+j2Z = 103+j 10ΩBoth branches are parallel,Total…

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 2, (b)…

A: In this question, find the instantaneous current with different different impedance. Draw the…

Q: 2. A current source in a linear circuit has is = 8cos(500nt – 25°) %3D (a) What is the amplitude of…

Q: Given the circuit shown below while assuming a sinusoidal steady state, 500 250 0 2 A 10 V1 •j 50 0…

Q: QI: Draw the impedance diagram for the series R-C circuit for the figure, then find the : Q2: For…

Q: Two loads are placed in parallel across a 120Vrms 60Hz line. The first load draws 150VA at a Lagging…

Q: When the average real power absorbed by an impedance is zero, then the impedance is: Select one: O…

A: The real power is absorbed by the resistor only when there is a combination of inductor and…

Q: An ac motor with impedance Z, (4.0 A40) O is supplied by an RMS value of 220-V, 60-Hz source. You…

A: According to question: The real power taken by the load is calculated as

Q: A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this…

A: Impedance: Impedance of a circuit is the combination of all the resistance as well as reactance. It…

Q: 6. Fill in the following table U.S Power System Standards Fill in the table for a correctly wired…

A: U.S National Electric code for voltage and frequency would be 208 V (Line-Line ), 60Hz…

Q: Three branches having impedances of 3+j4 Ω, 16−j12 Ω, and−j4 Ω, respectively, are connected in…

A: Given data: Impedance Z1 = 3+j4 Ω Impedance Z2 = 16-j12 Ω Impedance Z3 = -j4 Ω The admittance of the…

Q: Now write the time domain function, assuming 60 Hz operation for the following rms phasors; repeat…

Q: Q2: For the circuit in the figure, find: R = 41 16mH 265LF ll + UL - + UR - Da e = 70.7 sin 377t a)…

Q: The circuit shown in Figure having resistor 130 Q and a capacitor 50 µF is connected to a 210 V, 50…

A: We need to solve given RC circuit.

Q: 50 Q.20: For the circuit shown, find the transient mesh currents i, & iz as a function of time by…

Q: An electromagnet is modeled as L=0.3H and R=200 in series, and connected to a 120V(rms) sinusoidal…

A: Solve the above questions

Q: The circuit shown in Figure having resistor 200N and a capacitor 50 µF is connected to a 230 V, 50…

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (d) resistance of 10 ohms,…

A: Supply voltage = 150 vrms F = 50 hz so the supply voltage we can take (V) = 1502sin(ωt)…

Q: The circuit below is operating in ac steady-state. The source voltage is 25/2 sin (4000t) v. Vs =…

Q: R-C Series Circuit. In an AC series circuit containing capacitance C and resistance R. Which of the…

A: Use basic electric circuit laws and phase diagram technique. According to kvl sum of the voltages in…

Q: please write the complete solution and the topic is AC parallel circuits thank you A sinusoidal 50…

Q: 2. A sinusoidal e.m.f. 110 sin 400t volts is connected in series in a circuit with an inductance of…

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (a) resistance of 10 ohms,…

Q: 10 2 13.263 mH 73.683 µF Figure #6 Figure #6 shows an impedance consisting of resistance, inductance…

A: (a) Write the expression for the voltage when the frequency is in third harmonics and then find the…

Q: a) CONSTRUCT THE FREQ. DOMAIN EQUIV. CKT. CAL CULA TE THE STEADY VTATE CURRENT į by PHASOR. METHOD.…

A: In this question we need to construct the given circuit in frequency domain and we need to find…

Q: a. The following 40Ω capacitive reactance and 60Ω inductive reactance are in series with a 30Ω…

A: as per our guidelines, we are supposed to answer only one question. Kindly repost other questions as…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

A: As per the guidelines of Bartleby we supposed to answer first three subpart only for solution of…

Q: Transform the circuit shown in the figure into the phasor domain and determine (t). Assume that vt)…

A: In the circuit Find the current i(t) using the phasor Inductive Reactance X=wL Capacitive Reactance…

Q: If a current 5.0 A lags the applied voltage 230 V by an angle o, it can be resolved into two…

Q: 1844. Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal voltage source has…

Q: v1(t) = 12 cos(377t) v2(t) = 5 cos (377t) R1 3 kN R2 8 kN C1 450 nF b ww ww C2 600 nF L1 5 H v7(t)…

Q: It Given : VT = Vm cos wt Vm = 310V 2) f = 60HZ = 28 2 R4 L, - 0.06 H Find: Ca) RMS caleu lated…

Q: for the circuit shown in the figure below, find I, Vr and Vc, and the corresponding sinusoidal…

A: In this question we need to find a VR , Vc , I and average power.

Q: In an electric power system, it is given that the effective impedance of the generator station is Rs…

Q: Using your knowledge of the concept of expressing sinusoids in terms of

Q: power and average power absorbed by the passive linear network when the sinusoidal sources are given…

A: For instantaneous power just simply multiply the Voltage and current expression. For average power…

Q: 3. A series RC circuit with R=4k0 and C=0.40µF is connected to an AC voitage source v{t)=100sin200t.…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: When the average real power absorbed by an impedance is zero, then the impedance is: Select one: a.…

Q: Q2: For the circuit in the figure, find: 16mH 265LF R=42 + UR - + PL + vc e= 70.7 sin 377) a) Find…

A: Voltages and current of the given circuit are calculated as shown below

Q: R1 3002 V1 |120Vrms C1 60HZ 8.84uF 0°

Q: A certain industrial load has an impedance of 0.6 angle 30 ohms at a frequency of 60 Hz. What…

A: In this question, We need to determine the value of capacitor C to decrease the total angle from 30…

Q: Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: Determine the total equivalent impedance of the circuit as shown. Note: the student must put the…

A: In this question, choose the correct option All are parallel branches so What is equivalent…

Q: For the circuit shown in the below figure, the value of capacitor 'C' such that the power factor…

A: Given circuit is - Given that power factor is unity.

Q: When a series RC circuit is connected to a dc voltage, the circuit current reaches 63.2% of it final…

A: In this question we need to check the given statement is true or false

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x. The…

Question

100%

A given circuit has a resistor (R=20 ohms) and an inductor (L=0.3 henrys) connected in series with a
sinusoidal voltage with the following equation:
v(t) = 120v2cos (120t + 10°)
a.) Find the current immediately after switching
b.) Find the magnitude of impedance (in ohms)
c.) Find the steady-state RMS current in amperes

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
draw the thevenin equilvalent circuit and determine the load impedance for maximum power transfer. show the final circuit with appropriate resistors, capacitors, and/or inductors.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees