A geothermal powerplant uses steam that enters  a nozzle @ 973.15 K at 300 kpa under a velocity of having 20 m/sec, such that the steam exits at  200 kpa. The operator provides the process that is adiabatic and reversible. Calculate the ff. a. going out velocity of steam b. the going out temperature c. the sp. enthalpy at going out.

Q: Air plane working with Boot- Strab with evaporating cooling has 20 TR. If the exit air of…

A: To Find : The refrigeration effect and mass flow rate and COP. Given : The evaporating cooling is…

Q: An adiabatic air turbine has an inlet of 1600 K, 2000 kPa, and it exhausts at 100 kPa. If o=0.5…

A: The inlet temperature of adiabatic air turbine is .The inlet pressure of the adiabatic air turbine…

Q: An ideal gas, with C,- 0.529 Bhib.°R and R - 96,2 ft-lb/lb.°R, expends from 5 Nand 80°F to 15 A'…

A:

Q: 3) A steam with a quality of 9%, enters an adiabatic nozzle at 3.5 MPa and leaves at 0.4 MPa and…

A: GIVEN :- x=0.09 P1=3.5 MPaP2=0.4 MPaT2=140°CV2=2.7 m/s   SOLUTION :- we know,at P1=3.5 MPahf=1049.73…

Q: Question: Superheated vapor ammonia enters an insulated nozzle at 30°C, 1000 kPa, with a low…

A: The given information in the problem is shown in the following attached image:

Q: 2. A steam turbine inlet is at 2000 kPa, 500°C and the exit pressure is 1000 kPa. If the turbine is…

A: Given, P1 = 2000 kPa = 2 MPa T1 = 500°C P2 = 1000 kPa T2 = ? w = ?

Q: 3) A steam with a quality of 49%, enters an adiabatic nozzle at 3.5 MPa and leaves at 0.4 MPa and…

A: Given Data steam Quality, x=0.49 At P1=3.5 MPa At state 2 At P2=0.4 MPa T2=140°C C2=7 m/s

Q: Q1: A cylinder/piston contains 0.1m³ of air at 110 kPa, 25°C. The air is compressed in a reversible…

A:

Q: Refrigerant R 134 a enters an adiabatic heat exchanger at 140 kPa with a quality of 40% and a flow…

A: Given Data Working fluid is R134a Inlet condition  P=140 KPa, x=40% hf=27.08 KJ/Kg hfg=212.08 KJ/Kg…

Q: Aj Wet steam at 200 deg C has a specific enthalpy of 2300 kJ/kg (in the 2 phase region). Determine…

A: According to the guidelines we are supposed to answer 1st question only.

Q: 2. Steam at 4 Mpa and 400°C is received by a regenerative cycle. Before condensation at 0.005 Mpa,…

A: The T-s diagram of the system is

Q: In an engine, the air in a piston-cylinder arrangement has a compression ratio of 0.1. It starts…

A:

Q: A steam with a quality of 49%, enters an adiabatic nozzle at 3.5 MPa and leaves at 0.4 MPa and 140…

A:

Q: Q6) A stream of water at 85°C, flowing at the rate of (5 kg. s is formed by mixing water at 24°C…

A:

Q: An isentropic turbine process 5kg/s of steam at 4MPa, which is exhausted at 50kPa and 100 C. Five…

A: given data : mass flow rate at which the turbine processes steam (m*1) = 5kg/s pressure at which…

Q: Sketch and label the nozzle. Sketch and label the process on a P-v diagram, also mention all numbers…

A:

Q: Steam @ 500 C and 6 MPa expands in a turbine to 50 kPa and enthalpy of 2509, the turbine is not…

A:

Q: Urgentt.

A: Given-Information:- Inlet Temperature, T1 = 50°FInlet Pressure, P1,atm = 14.7 psig Delivered…

Q: Please be very detailed

A: Given data,

Q: A steam pipe carrying 400C, 200kPa steam enters a well-insulated mixing chamber where it is mixed…

A: P2=200kPa

Q: Air enters an adiabatic nozzle at 300kPa, 500K with a velocity of 10m/s. It leaves the nozzle at…

A: Given:P1=300 KPaT1=500 Kc1=10 m/sP2=100 KPac2=180 m/sA1=80 cm2Cp=1008 J/Kg.K

Q: Problem 4. Consider an adiabatic steam turbine operating at steady-state with a mass flow rate of 12…

A: GIVEN DATA- P1=10MPa T1=450'C C1=80m/s P2=10KPa C2=50m/s m=12kg/s