Solve this problem by creating a table. 273.A garden lawn spreader is powered by thewheels. The wheels are connected to thespreader by a set of gears. Determine thewidth of the swath that the fertilizer wouldbe spread.Assume the velocity of the fertilizer is equalto the velocity of the extreme tip of thespreader vane.Ignore the height of the grass.SWATHWIDTHNAME1.6 m/sSPREADER VANE DIAM = 22CMDB2/16/10GEAR2="DIAM = 4cmGEAR IDIAM=6CMSWATH WIDTHWHEEL DIAM = 27CmSPREADER VANE IS 30.cm ABOVETHE GROUND16B

The velocity of the wheel is .The radius of the wheel is .The diameter of the gear 1 is .The…

A garden lawn spreader is powered by the wheels. The wheels are connected to the spreader by a set of gears. Determine the vidth of the swath that the fertilizer would be spread. Assume the velocity of the fertilizer is equal co the velocity of the extreme tip of the spreader vane. Ignore the height of the grass.

A garden lawn spreader is powered by the wheels. The wheels are connected to the spreader by a set of gears. Determine the vidth of the swath that the fertilizer would be spread. Assume the velocity of the fertilizer is equal co the velocity of the extreme tip of the spreader vane. Ignore the height of the grass.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe P1 450mm in diameter, branches into two pipe (2 & 3) of diameters 300mm & 200mmrespectively. If the average velocity in the 450mm diameter pipe is 3m/s. Find; i) Discharge through the 450mm diameter pipe. ii) velocity on the 200mm diameter of pipe, of the average velocity in the 300mm pipe is 2.5m.
EXERCISE 1.10 The collar slides to the left as the interconnected bars swing in the vertical plane. The position of the collar is x = 20 sin (501) mm, and the angles are 0₁ = 0.27 сos (50t), 0₂ = 0.27 sin (50t - n/3) rad. Determine the velocity of the lower end by differentiating its position in terms of horizontal and vertical components. (Hint: Use the left fixed end of the bar as the origin of the frame. x direction is along the bar to the right while y direction is perpendicular to the bar downward.) L₁ F₂
A fabricated assembly made from three different sizes of standard steel tubing is shown below. The larger tube on the left carries 0.072 m3/s of water. The tee branches into two smaller sections. If the velocity in the 50-mm tube is 12.0 m/s, what is the velocity in the 100-mm tube? Ans. 7.88 m/s
Pumps: Two geometrically similar pumps are running at the same speed of 1000 rpm. One has the impeller diameter of 0.4 m and discharge of 30 liters/sec against a head of 20 m. If the other pump gives half of the discharge rate, then determine the head and diameter of the second pump. Answer: D=0.317 m, H=12.6 m
The local Amazon warehouse is looking to increase package delivering efficiency. They are testing a new conveyor belt system. Boxes are transported from one end of the factory to the other on this conveyor belt, with a velocity of vo. They eventually reach the end of the conveyor, where they slide onto a fixed incline section with uk = 0.40. The start of the inclined section is Point A, and the end is Point B. Determine: a) The velocity of the conveyor belt if the boxes leave the incline with a velocity of 8 [ft/s] Use the following diagram. Hint: Consider a box. Find its kinetic energy at point B. Find the works done by all the applied forces to the box, from point A to B. Use principle of work and energy to find kinetic energy and velocity of the box at point A. The solution is independent of mass, but for simplicity of solution, you can consider mass as 1 slug. 20 [ft] A 15°
At A, a 907.1848-g slider is pushed upward along a fixed curved bar in a vertical plane. Determine the rate (m/s2) at which the speed of the slider is decreasing. The slider's speed is 3048 mm/s as it passes point B. The radius r of the curved bar is 609.6 mm. B \ 30
1. Calculate the kinetic energy of a body which has a mass of 5 kg and velocity of 10 m/s. 2. In a non-flow process carried out 5.4 kg substance, there was a specified internal energy decrease of 50 kJ/kg and a work transfer of the substance of 8.5 kl/kg. Determine the heat transfer and a state whether it is gain or loss. 3. A gas is contained in a cylinder with a moveable piston on which a heavy block is placed. Suppose the region outside the chamber is evacuated and the total mass of the block and the movable piston is 102 kg. When 2140 J of heat flows into the gas, the internal energy of the gas increases by 1580 J. what is the distance through which the piston rises? 4. Calculate the increase in internal energy of a gas in a closed system during a process in which of heat is supplied to the system and 400 J of work is produce. 5. Convert the following readings of pressure to kPa, assuming the barometer reads 760 mm Hg. a. 90 cm Hg gauge b. 40 cm Hg vacuum c. 1.2 m H20 gauge
Find the specific speed of the pump, if the discharge through the pump is 160 liters/sec, speed is 1000 rpm and head is 27.5 m. Select one: O a. 4.87 O b. 33.33 O c. 23.33 O d. 13.33
Determine the displacement of a six-cylinder engine with a bore of 10cm and a stroke of 8cm.
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200 150 - 125 - Suction lines 100 - 90 - 3 65 - 2 50 Discharge lines 40 32E 25 E 15 20 200 400 600 800 1000 2000 4000 6000 8000 10000 10 100 Volume Flow Rate, Q (gal/min) 6 8 10 ++++ 15 20 25 30 40 +++++++++ ++++++++++++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 Volume Flow Rate, Q (m/h)
Consider a helicopter flying in a straight path at a speed of 52 m/s. The the rotor diameter is 10 m and the rotors are moving at 264 RPM (revolutions per minute). What is the maximum rotor tip speed (in m/s). Hint: Note that the rotor will sometime be moving in the direction of the flight path and at other times opposite to the flight path or at an angle to the flight path. The maximum rotor tip speed is generated when the rotor is moving in the direction of the flight path.
A projectile is launched with a speed v0 = 50 m/s at angle = 35°. How long does it take to reach the maximum height? y vo x 0 2.55 s 28.68 s O2.92 s O 5.10 s