A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is dhose=8 cm, and it reduces to d nozzle= 6.84 cm at the nozzle exit. If it takes 50 seconds to fill the bucket withwater, determine average velocity m/s of water at the nozzle exit.NozzleGardenhoseBucket

Answered: Image /qna-images/answer/a88990c3-e822-4119-8b04-cb6a00557dab.jpg

A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is d hose=8 cm, and it reduces to d nozzle3D6.84 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with water, determine average velocity m/s of water at the nozzle exit. Nozzle Garden Bucket hose

A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is d hose=8 cm, and it reduces to d nozzle3D6.84 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with water, determine average velocity m/s of water at the nozzle exit. Nozzle Garden Bucket hose

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Centrifugal pump is a kinetic device and uses the centrifugal force to push out the fluid. So the liquid entering the pump receives kinetic energy from the rotating impeller. The centrifugal action of the impeller accelerates the liquid to a high velocity, transferring mechanical (rotational) energy to the liquid. What makes Centrifugal Pump not to beclassified as a Positive Displacement Type of Pump? Is that the reason why cavitation will occur in centrifugal pumps and not in Displacement pump?
plzzzz help meeee
A pipe (1) 550 mm in diameter branches into two pipes (2) and (3) of diameters 300 mm and 20 cm respectively. If the average velocity in 550 mm diameter pipe is 4 m/s, find (i) discharge through 550 mm diameter pipe and (ii) velocity in 20 cm diameter pipe if the average velocity in 300 mm pipe is 2.5 m/s.
A Pelton wheel develops 750 kW under ahead of 200 m. Its nozzle has a diameter of 10 cm and losses in the pipeline due to friction amount to 90 Qʻ, where Q is discharge in cubic meters per second. Assuming the gross head and efficiency of the wheel to be constant and Cy for the nozzle as 0.98. Find the discharge and overall efficiency. If the power developed is reduced to 650 kW by (i) Operating the needle in the nozzle and
A pipe of diameter 11 cm conveying 200 liters/s of water has bend of angle (θ = 90⁰if last digit is zero/even and θ = 0⁰ if last digit is odd) through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively.
3. (a) A nozzle of inlet area A₁ and exit area A2 exhausts to atmosphere. A fluid of density p enters the nozzle with pressure p₁ (gauge) and velocity u₁. Show that the force trying to separate the nozzle from the pipe is given by 2 F = P₁A₁ - pA₁u₁² whether the nozzle is frictionless or not. A₁ A₂ -1)
While filling up your car with gasoline, you notice that it takes 3 minutes to dispense 55 liters of gasoline through the 2.5 cm diameter hose. What is the average speed, in m/s, of the gasoline inside the hose?
The water level in a tank open to the atmosphere is 20 m above the ground. A hose connected to the bottom of the tank is equipped with a nozzle at the end pointing straight up. In the line leading from the tank to the nozzle is a pump, which increases the pressure of water. If the water jet rises to a height of 27 m from the ground, what is the minimum pressure rise supplied by the pump to the water line? Assume no losses. 27 m 20 m O 59.3 kPa 75.8 kPa 68.7 kPa 72.5 kPa
Please solve it quickly I am at the exam
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
Calculate the resultant force required in kN to hold a 90° elbow in place when attached to DN 150 Schedule 40 pipes carrying water at 0.1768 m3/s and 1 050 kPa. Neglect energy lost in the elbow. Do not include direction for the final answer! NB: Assume a water density of 1000 kg/m3 and use appropriate appendix to obtain necessary data. Hint: Draw a diagram showing the pipe system with the bent at the bottom right corner, water flowing from left to right then up to help you analyse the problem. Sign Conversion: North (+) and West (+)
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.