show all steps in detail, units and formulas please. A frictionless pulley system is designed as shown with thesystem in static equilibrium. Cable AB has dimensions, a = 74ft., and b = 87 ft. If the block weights 726 lbs, and 0 = 34°,what is the force in cable AB?BlockBC< >

Answered: Image /qna-images/answer/2834dedb-576b-41a1-967c-f4365cd77640.jpg

Answered: A frictionless pulley system is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction please
Please show your neat work in Handwritten format
Draw the orthographic views of the following isometric figure. (Units in mm)
Hi there sir/madam I'm not sure how to do this question could please help with this The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is 25 mm and the stroke length for each cylinder piston is 275 mm. During engine testing, the engine runs at 4250 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 7.85 cm2 and diagram length of 3.25 cm. For a pressure scale set at 525 kN/m2 per cm on the indicator diagram, calculate the indicated power developed by the engine. To 2 d.p
6. Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).
Thank you for this answer. I don't quite understand step 4, 5 and 6 because the operation is not really readable : could you write it with parenthesis and clear opeartion signs (+, x, /, ^) ?
Draw the orthographic views of the following isometric figure.
Sketch a isometric drawing for each of the three sets of orthographic drawings
An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct statement below. The only way to generate multiple gear teeth is to sketch each tooth individually and then extrude each tooth individually. The engineer can use the linear pattern tool to create an array of gear teeth in a circular pattern about the center of the gear from a sketch of a single tooth. The engineer can use the circular pattern tool to create an array of gear teeth in a circular pattern about the center of the gear from a sketch of a single tooth. It is not possible to model gear teeth in SOLIDWORKS due to the complex shape.
Can I get some help looking over some sheets? I have most filled out, but just to double check for correctness and help with missing answers. Thank you
The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions per minute (rpm)) and the cube of the diameter. If the shaft of a certain material 2 inches in diamter can transmit 16 hp at 120 rpm, what must the diameter be in order to transmit 45 hp at 100 rpm? Round to 2 decimal places._______inches
Formula Sheet Calculator 0 = 90° -- 0 = 0° A A'

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A frictionless pulley system is designed as shown with the system in static equilibrium. Cable AB has dimensions, a = 74 ft., and b = 87 ft. If the block weights 726 lbs, and 0 = 34°, what is the force in cable AB? Block B C < >