A freezer sustains a cold environment of -24°C and exhausts its heat at 36°C. Assume a Carnot cycle. How much does it cost to remove 288 kJ of heat from the cold environment if the price of energy consumption is 13.5 cents per kWh? Express your answer in cents, to at least two places after the decimal point.

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: 10- The hook law is

A: To explain: The Hook's law. Explanation: If the force is applied to the material, then the material…

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: The triple thread screw has a lead of 15 mm. Determine its thread per inch.

A: Given               Lead, L = 15 mm                           = 0.59 in No of thread, n = 3 Find…

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: w of sine's when ( a= 100° , A=10.8 B=6

A:

Q: 12-x2 了了少 Je

A:

Q: メ the beam ABG B Deternine the reaultantf the ine load

A: Point load between B to C uniform distribution of 1700 lb/ftP1=1700×8P1=13600 lb

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 400N 200 Z00 N さ

A: Given Data :

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: What does the internal moment cause?

A: Internal moment are actually the moments due to the resisting forces generated when the cross…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Q/ The moment about the centre of the bolt is 0.2 m 0.03 m O 20.21 N.m O46.411 N.m O 55.626 N.m 300…

A:

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: What is the moment-area method?

A: The moment-area method is one of the methods for determining the slope and deflection generated in a…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: The vertical force T = 121 kN is applied to the frame. Given: L1= 38.9 m; L2 = 5.7 m; L3 = 4.2 m.…

A:

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: I start from 2f₁= max, derive to this expression {fy = may, 2) ap(x, y, z) dx (_ ap(x, y, z) ay

A: For the solution refer below images.

Q: C.W. ;DRAW: 1-FRONT+TOP+RIGHT SIDE 2-FRONT SECTION+TOP SECTION FROM MIDD. +RIGHT SECTION FROM MIDD.…

A: It is asked to draw the front, top and side views of the given model and also the corresponding…

Q: (b) 1489.5m³ (C) 128

A: given:bore diameter d=68mmstroke length l=75mm

Q: Consider (Figure 1). Figure 0.3 m. 120° 45° 60⁰° 325m Y Part A Determine the magnitude of the…

A: Given data: Force (F)=260 N To find:-the magnitude of the moment of the 260-N force about the x…

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data  bore diameter = 102 mm = 0.102m stroke length  = 120mm =0.120m number of cylinders =6…

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: A 5 ft DU B 5 ft -3 ft-

A:

Q: 4 in 2 in 4 in 8 in -12 in 16 in-

A: Given data To determine the moment of inertia and radius of gyration about x and y axis

Q: 200 p 6 10 I 10 K 10 Oetermine the alue the Reachion A 2 Determine the valueg the Reachom L 9, the…

A:

Q: Draw the front, Side and top

A: According to the question we need to draw the three orthographic projection views of the given…

Q: The bar AB shown in Figure 12-13 moves so that its lowest point A travels horizontally to the right…

A: Given information Velocity of point A, Find  Velocity of point B ,

Q: is the moment clockwise or counterclockwise?

A: Moment about point O is given by, C→MO=28.282 i^-19.148j^-5.13k^ The direction of moment is shown in…

Q: Reselve the 4501b fovce intoeom ponentsacting atong members ABandAC 30 45 450

A:

Q: //// // R R J3 Js Jy J. J8 R lt)

A: given; mass of block=mweight of block(w)=mgforce=F