A fluid moves in a steady flow manner between two sections in a flow line. At section 1, the area is 10 ft^2, velocity is 100 fpm, specific volume is 4 ft^3/lb. At section 2, the area is 2 ft^2, and the density is 0.2 lb/ft^3. Calculate (a) the mass flow rate at section 2. Calculate (b) the speed at section 2.

A fluid moves in a steady flow manner between two sections in a flow line. At section 1, the area is 10 ft^2, velocity is 100 fpm, specific volume is 4 ft^3/lb. At section 2, the area is 2 ft^2, and the density is 0.2 lb/ft^3. Calculate (a) the mass flow rate at section 2. Calculate (b) the speed at section 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wind tunnel has an inlet section with a velocity of 360 ft/s at standard atmospheric conditions. The airflow moves towards the throat, and the pressure decreased to 2010 lbs/ft^2. What is the velocity at the throat?
1. A fluid moves in a steady flow manner between two sections in a flow line. At section 1: A_1 =2 ft^2; 9_1 = 100 fpm; v_1 = 4 ft^3/lb. At section 2: A_2=2 ft^2; p_2=0.20 lb/ft^3. Calculate the mass flow rate in Ib/min.
Water with a density of 1 g/cm³ flows through a horizontal pipe. The pipe cross-section tapers from 80 cm² to 40 cm² at a reducer. The static pressure before the reducer is 4 bar and the flow velocity is 4 m/s. The flow is incompressible and frictionless (inviscid). What static pressure is measured after the reducer?
Steady State flow exists in pipe that undergoes a gradual expansion from a diameter of 6in. Assuming constant density and the inlet flow velocity is 22.4 ft/sec. What is the size of the exit pipe if the exist flow velocity is 12.6 ft/sec?
A certain SSSF control volume with a single inflow and outflow and has an inflow speed V₁ = 200 meters / sec and outflow speed Ve = 1000 meters / sec, with a mass-flow-rate m(dot) = 5 kg/ sec. Find the time rate of change of the kinetic energy between the outflow and inflow streams in kW (units must be correct).
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
A fluid moves in a steady flow manner between two sections in a flow line. At section 1: A_1 =2 ft^2; ϑ_1 = 100 fpm; v_1 = 4 ft^3/lb. At section 2: A_2=2 ft^2; ρ_2=0.20 lb/ft^3 . a.) Calculate the mass flow rate in lb/min. b.) Calculate the speed at section 2 in ft/min or fpm
3). in the figure below. Consider the acceleration due to gravity as g=32.2 ft/s², specific weight of water as yw-Pwg=62.4 lb/ft³ and gasoline as ygasoline=Pgasolineg=42.5 lb/ft³. What pressure, pi, is needed to produce a flowrate of 0.09 ft³/s from the tank shown Air Gasoline 2.0 ft Salt water 3.6 ft SG = 1.1 0.06-ft diameter -
Water enters a PVC manifold (1) and exits the manifold through three equal diameter branches (2, 3 Q3. and 4), as shown. Assume the flow divides equally between the three branches, and that all the dimeters are the physical inside diameters. Calculate 1. ) the volumetric flow rate, Q, in each exit branch in units of L/s 2. ) the velocity, V, in each exit branch in units of m/s D2 = D3 = D4 = 10.0 mm %3D %3D 2 4 Outlet Branches: 2, 3, 4 Closed Inlet V, = 2:00 m/s D, = 25.0 mm PVC Manifold
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluidby varying the cross-sectional area. At the last section of a jetengine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s ata pressure of 500 kPa and a temperature of 600 K enters a nozzlewith an inlet cross-sectional area of 5 m2. The exit area of thenozzle is 20% of its inlet area. The air leaves the nozzle at avelocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (iv) Determine the temperature of the air as it leaves the nozzle.(v) Calculate the pressure of the air as it leaves the nozzle.
Q2/When the pump in Fig. below draws 220 m³/h of water at 20°C from the reservoir, the total friction head loss is 5 m. The flow discharges through a nozzle to the atmosphere. Estimate the pump power in kW delivered to the water. D= 12 cm D= 5 cm V, 2 m Pump 6 m Water
The suction condition of an air compressor is 104 kPa, 28 deg.C, and 6.81 m^3/s. If the surrounding air is 135 kPa, 32 deg. C Determine the free air capacity in m^3/sec. Answer in whole number