A centrifugal pump operating under steady flow conditions delivers 3000 kg of water per minute at 20 degrees * C . The suction pressure is 0.8 bar and delivery pressure is 3 bar. The suction pipe diameter is 15 cm and discharge pipe diameter is 10 cm. Find the capacity of the drive motor. Neglect the change in internal energy and assume that the suction and discharge are at same level

Q: Data measured during tests of centrifugal pump driven at 3000 rpm are Parameter Inlet, Section 1…

A: Given: speed of the pump→N=3000 rpm Hence rotational speed→ω=2πN60=2π×300060=314.16 radsec because…

Q: 4.8: A steam nozzle admits steam at 7 bar and 275 °C. The throat diameter is 5 mm. Expansion of…

A: As steam expands from a higher pressure to a lower pressure, a portion of its enthalpy is…

Q: 1. A centrifugal pump operating under steady flow conditions delivers 2270 kg per minute of water…

A:

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: When one row of nozzle is followed by another row of blades, it is known as a stage of turbine. In…

Q: the following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: Given Steam velocity = 630 m/s Mean blade velocity = 125 m/s Nozzle angle = 16o First row outlet…

Q: A fan delivers 4.804 m^3/sec at a static pressure of 5.245 cm of water when operating at a speed of…

A: Given data: Q1=4.804 m3/sQ2=9.103 m3/sP1=5.245 cm of water Need to determine the pressure in cm of…

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: When one row of nozzle is followed by another row of blades, it is known as a stage of turbine. In…

Q: The characteristic curves of load versus the flow of a centrifugal pump are shown in figure P6.80.…

A:

Q: Laboratory tests on a centrifugal pump, which is directly coupled to a motor running at constant…

A:

Q: Q5/ A centrifugal pump impeller runs at 1500 rpm & has internal & external diameters of 0.2 n & 0.4…

A: A centrifugal pump is a mechanical device that moves a fluid by transferring rotational energy from…

Q: PROBLEM: A nozzle having a velocity coefficient of 0.98 discharges a jet 15 cm in diameter under a…

A:

Q: d is 10 m/s, the water jet velocity is 25 m/s and volumetric flow rate of the jet is 0.1 m³/s. If th

A: GIVEN:pheriferical speed U=10m/sjet speed V=25m/sQ=0.1m3/sϕ=180-120=600

Q: A Roots blower supplies air at the rate of 1 kg/s. The pressure ratio of the blower is 2:1 with an…

A: We know that a roots blower delivers 1 kg/s of air.The blower's pressure ratio is 2:1, with an…

Q: For a certain stage of an axial flow turbine, the nozzle makes an angle of 28' with the wheel…

A: Given data as per question Axial velocity =500 ft/s Degree of reaction =50% blade velocity(u)=550…

Q: 1. An air compressor works with air at 20 °C compressing the air from 1 bar absolute (105 N/m²) to…

A: To find: The specific work and head generated. Given: The initial temperature is T=20°C. The initial…

Q: Calculate the total head of a centrifugal pump and use the Darcy equation in computing the friction…

A:

Q: Q1// the velocity of steam at inlet to simple impulse turbine is 1000 m/s and the nozzle single is…

A: Given dataVelocity V1= 1000m/secBlade speed Vb = 400m/secNozzle angle α = 200To determine Blade…

Q: 3. For a Pelton turbine the pressure of the flow before the nozzle is 5 bar while the velocity of…

A: As given that the pressure before the nozzle(P) = 5 bar ;the velocity of the flow leaving the nozzle…

Q: The pressure of the water base of a Pelton Wheel is 4850 kPa and the velocity at the same point is 6…

A:

Q: Q3/ Boeing 777 Turbofan engine, air enters ambient conditions (1 bar and 15°C) enters a three stage…

A: Given:P1=1 bar =1*105 N/m2T1=15°C =288 KC1=120 m/s =Ca1α1=0rmean=0.2 mN=9000 rpmβ1-β2=rotor turning…

Q: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95…

A:

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Air passes through a narrow section during horizontal flow. The initial air temperature is 21 [℃],…

A:

Q: . The total dynamic head in ft. b. The water power in horsepower

A:

Q: EX1: Given are the following data for a commercial centrifugal water pump: ri =10 cm, r2 = 17.5 cm,…

A:

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: When one row of nozzle is followed by another row of blades, it is known as a stage of turbine. In…

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the flrst…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: Q5/ A centrifugal pump impeller runs at 1500 rpm & has internal & external diameters of 0.2 m & 0.4…

A: Given that, Speed of the pump, N=1500 rpm,Internal diameter of pump, d=0.2 m,External diameter of…

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: When one row of nozzle is followed by another row of blades, it is known as a stage of turbine. In…

Q: An inward flow reaction turbine has an external and internal diameters of runner 67.5 cm and 50 cm,…

A:

Q: 2. The diameter of the discharge pipe of a pump is 15 cm and that of the intake pipe is 20 cm. The…

A:

Q: Seven hundred gallons per minute of water are being discharged by a centrifugal pump 5 ft above the…

A:

Q: Pump Tutorial A centrifugal pump is used to pump a liquid with the properties given below. Liquid is…

A:

Q: A Francis turbine has the following specifications. Inlet radius 300 mm, outer radius 150 mm, flow…

A: givenouter radius of the runner ro=300mminner radius of the runner ri=150mmoutward  flow reaction…

Q: A two-lobe rotary positive-displacement pump moves 0.60 cm3 of motor oil in each lobe volume. For…

A: Given: The volume of each lobe is Vlobe=0.6 cm3. The number of lobe is N=2. The rate of rotation of…

Q: A fan manufacturer rates his fans at 152 mm water gage static pressure for 10 m' of air per second…

A: Write the given data.   h1=152 mm  h2=130 mm   η=69%N1=1200 rpm Here, h1 is the water gauge static…

Q: Water vapor with a pressure of 160 bar and a temperature of 480°C enters a stable turbine with a…

A: Given:-At inlet 1;P=160 barT=480°CQ1=800 m3/minAt outlet 2;P=5 barT=240°CV2=25 m/sAt outlet…

Q: The Head -flowrate curve for a centrifugal pump is given by: Hp = 28 -30Q2 Where, Hp is in meter and…

A:

Q: The rate of flow of water in a pump installation is 60.6 kg/sec. The intake static gage is located…

A:

Q: 1)  A plot of pump net head is shown below. Two curves are drawn: blue color curve and red color…

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: 4.) Each of the four jet engines on an Airbus A380 airliner develops a thrust (a forward force on…

A:

Q: 3. For a Pelton turbine the pressure of the flow before the nozzle is 5 bar while the velocity of…

A: Option :a  V0=31 msecD=1.5 m ,N=500 rpmPressure nozzle P=5 bar P=ρgHH=5×1051000×9.81H=50.96 m…

Q: Three pumps are connected in series. According to pump performance curves, the free delivery of each…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: n ideal water jet with volume flow rate of 0.05 m^ 3 / s strikes a flat plate placed normal to its…

A: Given:Volume flow rate of water jet, Q=0.05 m3/sForce, F=1000 NDensity of water, ρ=1000 kg/m3

Q: A single pump and system have characteristics as shown on the graph below. Based on this…

A: A single pump and system have characteristics as shown on the graph below. Based on this…

Q: A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.