A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.

Q: A belt drive is to be used for transmitting 3KW from an electric motor whose speed is 1500rpm to a…

A: The reduction of the gearbox or gear ratio is evaluated by dividing the larger gear teeth number by…

Q: 3.A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing…

A: Answer: The maximum axial intensity of pressure between the discs: 0.12665 MPa.

Q: Calculation for drive system and rack/spur gear of a crane. System needs to able to climb an incline…

A:

Q: With a driveshaft turning at 2000 rpm , I then have a spring that can rotate a shaft 5000 rpm, I…

A: Given that, Speed of driveshaft, N=2000 rpm,Speed of spring shaft, N=5000 rpm,

Q: Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0…

A: GivenI=80 lb-ft2N1=0  to N2=1500rpm in t=3sTstart=10 in lb=1012 lb ft=1012×32.17 lb ft=26.808 lb…

Q: A multiflex flexible coupling, transmitting 15 kW power at 720 rpm, is shown in Fig. 9.46. It…

A:

Q: (c) The type of pressure plate chosen as a result of the calculation in part (b) of this question…

A: A clutch is a device that allows two elements with a common axis of rotation to connect and detach…

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: Calculate the capacity ol a bucket conveyor. The parameters are as follows.Belt speed 2.5 m/sec,…

A:

Q: m diameter at 200rpm The coffiecient of e belt and the pully is (0.25),angle of contac ximum tension…

A:

Q: 4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a…

A: Given: P = 38.5 hp = 28.71 kW N1 = 650 rpm N2 = 200 rpm T1 = 21 teeth Ks = 1.6

Q: Determine the given question with correct solution

A: Given data; P=25 KW=25×103 WN=300rpmp=85 KN/m2=0.85 N/m2d2=380 mmr2=190 mmn=2μ=0.25 Find,1.outer…

Q: (c) Find the smallest number of teeth theoretically required (in order to avoid interference) on a…

A: C) Given: Pressure angle (φ)=22.5°

Q: 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears havir 0°…

A: given,p=15 kwNm=1200 rpmNc=300 rpmL=400 mm(σ)p=210 mpa(σ)G=140 mpanow , let face width ,b=10 mmand…

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given                      Power, P = 5 kW Coefficient of friction = 0.25  Constant pressure, P = 1…

Q: (b) A multiple plate clutch has more number of clutch plates. A typical clutch consist of the…

A:

Q: Q2) A flat belt drive system is to be) designed for an application in which the input shaft speed is…

A:

Q: Design a V-belt system to transmit a power of (24) Kw between two shafts at (1200) rpm with a…

A: Write the rated power. Prated=25 kW   Calculate the Design power. Pdesign=PratedSF=251.4=35 kW

Q: the efficiency is

A: Given; In order to test the efficiency of reducer gear train, input is given as, 1 kWAt the end of…

Q: A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is…

A:

Q: rmine the pow

A:

Q: The client requires a single step up spur gearbox to transmit a 10kW power from a shaft rotating at…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the hp requirement to lift the load…

A:

Q: A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input…

A: Diameter of the motor shaft pulley = D1 = 1.33 cube root of Power / Speed max D1 = 1.33 cube root 25…

Q: Q1. An open belt drive configuration having 10 pulleys in total, the input and output speeds are 20…

A:

Q: . Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10…

A: Given:Diameter of the driving wheel, d=10 inSpeed of the wheel, N=200 rpmWidth of the wheel, w=2…

Q: Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0…

A: GivenI=80 lb-ft2N=0 t o N=1500 rpm in t=3sTstarting=10 lb-in=1012 lb ft=1012×32.17  lb ft2/s2=26.808…

Q: Design a chain drive to run a blower at 600 rpm. the power to the blower is available from a 8kw…

A: Given Blower NB = 600 rpm Motor power = 8 kW Motor NM = 1500 rpm Distance = 800 mm To find Chain…

Q: 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20°…

A:

Q: q4 part a plz provide handwritten answer asap

A: u asked only a part only so answer in hand written

Q: A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter…

A: GIVEN DATA-  m=585kg  dm=20mm p=5mm Coefficient of friction =0.1 We have to find torque required to…

Q: Calculate the retraction force output for a double acting linear actuator with a piston diameter of…

A:

Q: An engine of 175 mm bore and 375 mm stroke is governed by hit and miss type governor to 220 rpm.…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.