A flanged bolt coupling has eight 10-mm diameter steel bolts on 600 mm diameter bolt circle and six 20 mm diameter bolts on 300 mm diameter bolt circle. Determine the maximum torque that can be applied without exceeding the shear stress of 55 MPa for the bolts and for the rods. Use G = 80 GPa.

A flanged bolt coupling has eight 10-mm diameter steel bolts on 600 mm diameter bolt circle and six 20 mm diameter bolts on 300 mm diameter bolt circle. Determine the maximum torque that can be applied without exceeding the shear stress of 55 MPa for the bolts and for the rods. Use G = 80 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A bar having a radius equal to 0.375 inches is subjected to different torques along its span as…

Q: The solid-circular shafts are connected by gears at B and C as shown below, and having the same…

A: Given Data Shear modulus of shafts is:G=75 GPa Diameter of shafts is :Do=24 mm Length of shaft 1 is…

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

A: Given data: - The torque at point A is TA = 2T. The torque at point B is TB = 3T. The allowable…

Q: 4. The tapered shaft is made from E- 36 steel (G = 80 GPa ), and has a radius which can be described…

A: Given Torque, T = 450 Nm Length, L = 4 m Find Angle of the twist

Q: The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the…

A: Given data: The allowable shear stress in the magnesium bar is τmg=45 MPa The allowable shear stress…

Q: The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Calculated absolute maximum shear stress developed in the pipe. And the calculated angle of twist of…

Q: A cast-iron gear with 100-mm effective diameter and t = 40-mm hub engagemen length is to transmit a…

A: Given: R - 10 mm t - 40 mm T - 120 N.m ro - 50 mm Ec - 100 Gpa Es - 200 Gpa f - 0.16 v - 0.3 To…

Q: (a.) Determine the maximum length of the flexible shaft consists of a 5mm -diameter steel wire…

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr Tmax Ip Ex

Q: Q6/ The shaft is made from a solid steel section AB and a tubular portion made of steel and having a…

A: Torque = 50 lb.ft Gst = 11.5 x 103 ksi GBr = 5.6 x 103 ksi

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

Q: The composite shaft of total length is 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm…

Q: A shaft is made of a steel alloy having an allowable shear stress of 10 ksi and the diameter of the…

A: Data givem - Shaft is made of steel alloy Allowable shear stress τallow = 10 ksi d = 1.2 inch…

Q: d3 T3 T2 T1 d1 TP. B L3 L2 L1.-

A: The polar moment inertia of a circular cross-section is defined as moment of area about the axis…

Q: The brass wire has a triangular cross section, 2 mm on a side. If the yield stress for brass is tY =…

A: Given Data: Side of triangular section is a =2 mm. Yield stress of shear is tY = 205 MPa. Length of…

Q: An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress…

A: Given Data Diameter of bar AB is : d1=90 mm Diameter of bar BC is : d2=60 mm Allowable stress is :…

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

Q: For the solid circular rods exposed to the shown torques, determine the segment that experiences…

Q: A flanged bolt coupling consists of ten steel 2-in.-diameter bolts spaced evenly around a bolt…

A: Given data, n= 10 d= 0.5 in D= 14 in , R= 7 in τ= 6000 psi.

Q: If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a…

Q: The tube is made of C86100 bronze and has a rectangular cross section asshown in Figure. If it is…

A: The FBD of the system is as follows:

Q: Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and…

A: Given: Straight bar ABCD, Length of Parts AB, BC, CD = 500 mm

Q: A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the…

A: Torque T = 2 kip in = 0.16 kip ft thickness t = 0.1 in rm = (2 + 1.9)/2 in =1.95 in Am = π4 rm2=…

Q: A flange bolt coupling consists of 10-15mm diameter steel bolts on a bolt circle 300mm in diameter…

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

Q: A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

Q: Two 20 mm steel shafts with a 100 MPa yield stress in shear are connected by a brass coupling with…

A: Given, d1 = 20 mmτsteel = 100 MPaτbrass = 60 MPaFOS = 2.1∴ τallow-steel = 1002.1 = 47.62 MPa&…

Q: A torque of TD- 1235 N-m is applied to gear D of the gear train shown. The bearings shown allow the…

A: GIVEN DATA TWO SHAFT GIVEN CONNECTED WITH GEAR TORQUE IN SHAFT 2 T=1235Nm DIAMETER OF BOTH SHAFT…

Q: If a = 25 mm and b = 15 mm, determine the maximum shear stress in the circular and elliptical shafts…

A: Given: a=25 mm b= 15 mm T = 80 Nm To determine: The maximum shear stress in the circular and…

Q: Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer…

Q: Eight 10-mm diameter steel bolts on a bolt circle 150 mm in radius and six 20-mm diameter bolts on…

Q: A solid circular steel shaft having an outside diameter of 2.25 in. is subjected to a pure torque of…

Q: 4. The tapered shaft is made from E- 36 steel ( G = 80 GPa ), and has a radius which can be…

A: Given Torque, T = 450 Nm Length, L = 4 m Find Angle of the twist

Q: A flanged bolt coupling has ten 12-mm diameter steel bolts on 450 mm diameter bolt circle and six 12…

A: The shear stress on the bolt at a diameter of 200 mm can be expressed as, For 6 bolts, the maximum…

Q: The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a diameter of 25…

Q: QUESTION 1. Determine the constant thickness t of the square shaped tube if the average shear stress…

A: Given data: The average shear stress is; ? = 90 MPa. The magnitude of the torque is; T = 3 kNm. The…

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

Q: The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum…

Q: A flanged bolt coupling has ten (10) steel 25.4 mm diameter bolts evenly tighten around a 415 mm…

A: Given: n = 10 D = 25.4 mm R = 415/2 mm tau = 50 MN/m2

Q: The composite shaft shown consists of a bronze sleeve (1) securely bonded to an inner steel core…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

Q: While an oil well is being drilled at a depth of 2100 m, it is observed that the top of the…

A: Given data, L= 2100 m =2100000 mm d= 200 mm =200 mm G= 77.2 GPa=77200 N/mm² Revolution N= 2.5

Q: If a G1=77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the…

Q: The solid steel shaft carries the torques Tl = 750 N • m and T2 = 1200 N • m. using Ll = 1.0 = 2.5 m…

Q: While an oil well is being drilled at a depth of 2000 m, it is observed that the top of the…

Question

100%

A flanged bolt coupling has eight
10-mm diameter steel bolts on 600
mm diameter bolt circle and six 20
mm diameter bolts on 300 mm
diameter bolt circle. Determine the
maximum torque that can be applied
without exceeding the shear stress of
55 MPa for the bolts and for the rods.
Use G = 80 GPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Problem 1 shaft B A flanged bolt coupling has ten 12-mm diameter steel bolts on 450 mm diameter bolt circle and six 12 mm diameter bolts on 200 mm diameter bolt gircle. Determine the maximum torque (in KN-m) that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 80 GPa. V1 V2 R2 -coupling
A flanged bolt coupling has ten (10) steel 25.4 mm diameter boltsevenly tighten around a 415 mm bolt circle. Determine the torquecapacity of the connection if the allowable shearing stress inthe bolt is 50 MN/m2
The solid-circular shafts are connected by gears at B and C as shown below, and having the same diameter (D.). The shear modulus of the shafts is 75 GPa. All bearings allow free rotations of the shafts. Determine the rotation of free end A when a torque T is applied. The values of L1, L2, Do, and T are given in table below. Fixed L1 D 100 mm B 60 mm L2 Student ID 1152179 1155 L2 (mm) (mm) (mm) (N.m) 380 24 L1 Do 38
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. A 400 N-m 850 N-m L=1.4 m 30 mm diameter B L=2.4 m 50 mm diameter L-1.9 m 30 mm diameter
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. Student ID L1 (m) L2 (m) D (mm) 1131731 1 0.6 78
The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1168.7 Nm, U = 4515 Nm, x = 3.01 m, y = 2.36 m, z = 1.35 m, d = 90 mm, and e = 83 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places. U T Aluminum Steel Bronze
The halves of the coupling are held together by four 5/8-in.-diameter bolts. The working stresses are 12 ksi for shear in the bolts and 15 ksi for bearing in the coupling. Find the largest torque T that can be safely transmitted by the coupling. Assume that the forces in the bolts have equal magnitudes. 0.5 in. 3.5 in.
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa
A flanged bolt coupling consists of ten steel 2-in.-diameter bolts spaced evenly around a bolt circle 14 in. in diameter. Determine the torque capacity of the coupling if the allowable shearing stress in the bolts is 6000 psi. Numeric Response
A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 5°. T= 60 N.m (1) 1,800 mm 800 mm
Steel bar whose length of 1.31 m and a radius of 13 mm is subjected to torque which produce a shear. If the angle of twist is 30° and shear modulus of 203 GPa. Determine the torque applied.
Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at 'J. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA 600 mm 75mm 600 mm 50mm 800mm G. T2