Question 1: Equilibrium of rigid bodyThe uniform beam AD, which is supported by pin at point A and by roller at point C, carriesthe loads as shown in the figure below. Neglecting the weight of the beam and considering thesystem to be at equilibrium,(a) draw the free body diagram of the system(b) determine the reactive force at point C(c) determine the reactive forces at point A.120 kN/m-2m-100 KNB2 mC +120 kN/mo2m30⁰D120 kN

Answered: Image /qna-images/answer/d28bc24e-f0d5-4a2a-afb3-b2b6c847793d.jpg

Answered: (a) draw the free body diagram of the…

(a) draw the free body diagram of the system (b) determine the reactive force at point C (c) determine the reactive forces at point A. A 120 kN/m 2 m- | 100 KN B C 120 kN/m 2 m2 m- 30⁰ D 101 120 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 10-m beam is simply supported; a moving wheel load of 30 kN is imposed. Using the concept of…

A: Given data in question Load 30 kN Span 10 m Simply supported beam To find out Maximum moment at…

Q: With aid of diagram, elaborate on the method to test material hardness using Brinell hardness test

A: Brinell hardness test:- The Brinell hardness test is a common method used to determine the hardness…

Q: A beam is loaded and supported as shown below. (a) Determine expressions for the bending moment in…

A: To determine The bending moment for each section The single expression for bending moment using…

Q: Examine how the construction industry impacts on the environment, and how changes in the industry…

A: Here. It is asked to Examine how the construction industry impacts on the environment, and how…

Q: Check whether the bolts provided in the hanger connection as shown in figure are adequate. The end…

Q: 3. For the cantilever beam and loading shown, determine the following using double integration…

Q: 4.35 Bar AC supports two 400-N loads as shown. Rollers at A and C rest against frictionless surfaces…

Q: 5. A line AB is measured at both ends as follows: Instrument at point A, slope distance = 879.209 m,…

Q: A reservoir has average surface area of 20km². Mean rate of inflow is 10 m²/S mean outflow is 15…

Q: Determine the slope (in rad) at 3.3m from the left if P = 249kN, E = 25000MPa, and I = 223x105mm4.…

Q: 2. A cylindrical tank 1.5m in diameter contains a column of 3 immiscible liquids with SG 0.8, 1.0,…

Q: For Unsteady Flow Orifice, derive the formula in solving As in terms of h for the cross-section of…

A: It is asked to derive formula for the cross-section of Frustum of inverted cone in terms of h for…

Q: A rectangular simply supported beam of size 100 mm × 250 mm size and span 3 m is subjected to a…

A: Given Beam Determine the maximum shear stress in the beam.

Q: C 5 kN 45° A B D 1 m 45° 2 kN F 1 m E Determine the magnitude of the force (in kN) in member DE.…

Q: An embankment is shown in the figure. Determine the stress increase (in kPa) under the embankment at…

Q: A compound bar is made of a steel plate 50 mm wide and 10 mm thick to which copper plates of size 40…

Q: (use all 3 methods to estimate k and BODu) 2.50. A polluted river sample is analyzed using standard…

Q: 4 Solid waste from a park is to be collected in large containers. It is estimated that the average…

Q: The rigid beam embedded in the Figure is fixed at the top by two posts, one in AISI 4340 steel (dext…

Q: A structural of 200 mm long must be able to support a load of 100,000 N without experiencing any…

A: First we summarise the given data : Note - Density in Kg/m3

Q: In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to…

Q: Pr Plot mon system. Find the moment of inertia of the shaded area about the horizontal and vertical…

Q: (ITETTI A (7) t 21 4m C (1) t/m 41 4m D B I Frame dimensions and loads are defined in the figure.…

Q: Ex pie study of freeway flow at a particular site has resulted in a calibrate speed- density…

A: The speed density relationship is given as, V =57.51-0.008D= 57.5-0.46D Where v is the speed and D…

Q: A cubical block of side 0.4 m slides on an oiled (μ = 8 poise) plane horizontal surface. The oil…

Q: celeration a (positive if up, negative if down). Neglect the mass of t

Q: A lift irrigation scheme using a discharge of 100 m³/hr is planned to raise a crop with an average…

A: Given- Discharge Q=100 m3/hr, average delta =0.4 m Intensity I=50%, 3600 hours of working,…

Q: Different types of roofs

A: Roof is the topmost component of the building that provide structural covering to protect the…

Q: Find shear and bending diagram, and deflection of this structure. 4 K₁ rigid rigid

A: The diagram is provided. We have to find out the followings: Shear Force and Bending Moment…

Q: Problem 3: A W 460 x 147 is simply supported on a span of 8 m is laterally supported only at its…

A: Given: W 460*147, Span = 8m, Fy = 345 MPa

Q: During a particular stage of the growth of a crop, consumptive use of water is 3 mm/day. If the…

A: Given that :- Consumptive use of water = 3 mm/day if the amount of water available in the soil is…

Q: A vertical plate is an equilateral triangle whose edge is 3.5 m long. If one edge is level with the…

Q: A local arterial has an average flow of 1500 vph. At 8:20 AM, a school bus stopped at a local stop…

A: Given data: Average flow, q=1500 Vph Average spacing=8 meters Traffic capacity, qm=1800 Vph Using…

Q: How to find the time to fill the reservoir

A: If the volume of the reservoir and rate of discharge is given.. Time to fill the reservoir can b…

Q: For the section below, you need to work out the centroid position (dy and d₂ from the origin…

Q: A 늘- P 늘 B

A: A beam is given with a vertical roller at A and a horizontal roller at B. To determine the…

Q: If length of rod is 2 m and a radius of 20 mm is made of high-strength steel. The rod is subjected…

A: Solution: Given that : Length of rod = 2 m = 2000 mm Radius of rod = 20 mm Diameter of rod = 40 mm…

Q: Q. 3: needs A Traffic engineer urgently to determine The AADT on an urbon minor arterial highway. he…

A: Given data: Hourly volume observed during the 1st hour of Wednesday V1=560 v/hr Hourly volume…

Q: For a turbulent boundary layer (under zero pressure gradient), the velocity profile is described by…

A: Given- A turbulent boundary layer (under zero pressure gradient)- Velocity profile is 1/5th power…

Q: Calculate the deflection at a point of zero slope using double integration of method

Q: 5. How that the friction factor of the Darcy-Weisbach formula and the Manning's roughness factor n…

Q: Q.5 (a) The following forebearings and backbearings were observed in traversing with a compass. Line…

Q: -ing a particular stage of the growth of a crop, consumptive use of water is 3 mm/day. If amount of…

Q: The trap door is held open by the rope AB. If the tension in the rope is T = 70 kN, determine its…

A: T=70kN To find moment about y axis

Q: 4. A 4-hr storm rains on a 100 km² drainage watershed. The surface runoff data from a gaging station…

Q: Q.3 (a) A 30 cm × 15 cm venturimeter is provided in a vertical pipe line carrying oil of specific…

A: Given data Coefficient of discharge (Cd) = 0.98 Specific gravity of mercury (Sm) = 13.6 Specific…

Q: Examine how the construction industry impacts on the environment, and how changes in the industry…

A: Over the whole life cycle of a development, construction activities have an influence on the…

Q: shear force and bending moment diagrams as in Problem 1 to compute the maximum bending stress and…

A: Given data: A simply supported beam with concentrated moment and a point force of intensity 8 kN…

Q: 6. The 1780-kg car has a velocity of 27 km/h up the 12-percent grade when the driver applies more…

A: Given:- The mass of the car = 1780 kg The velocity of the car = 27 km/h The grade of the slope = 12…

Q: The loading of the truss is represented below. EA = 50 x 106 N Question 1. Determine the…

A: Given Data AE = 50 × 106 N Determine 1. Vertical displacement of joint-B. 2. Joint-C overall…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure shows a statically determinate beam under distributed loading conditions where C is the constant. 2x x? q(x) = C(- L AB A 2L/3 L/3 RA RB Figure 2 a) Determine the resultant of the distributed load where C is constant. Submit part Unanswered b) The magnitude and direction of the reactions at support B. Submit part Unanswered c) The magnitude and direction of the reactions at support A.
The value of M in the beam ABC shown in the figure is such that the joint B does not rotate. 30 kN/m aj v vvv v vy 4 m FR B The value of support reaction (in kN) at B should be equal to 6 m
The beam AB shown in the figure supports a uniform load of intensity 3000 N/m acting all over half the length of the beam. The beam rests on a foundation that produces a uniformly distributed load W over the entire length. 3000 N/m B w N/m 0.8 m 1.6 m 0.8 m 3.2m O Compute the value of W to be in equilibrium. Compute the max. shear force of the beam. Compute the max. m-ment of the beam.
Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. ... The beam is connected to the rest of the system by a pin joint at B and a roller support at ... Determine the magnitude of the reaction forces on the beam at the supports.
1. A 4.80-m long beam is subjected to the force shown. Reduce the given system of forces to (a) anequivalent force-couple system at A, (b) an equivalent force-couple system at B, (c) a single force ofresultant. Note: Since the reactions at the supports are not included in the given system of forces, the givensystem will not maintain the beam in equilibrium.
The beam shown in the figure is subjected to a concentrated force with Fo90 kN, a unitomy distribated force and two couples. A is a pin support and D a roller support (a) Determine reactive forces (b) Draw shear and moment diagrams and mark values at critical points. 10 kN/m 25 kN- m 60 kN - m 3 m 2 m -1 m-I m--
The figure shown is a beam subjected to varying loadings and a point load.a) Determine the magnitude and direction of the single equivalent force to the forcing systemshown. Specify its location on the beam from point B.b) Calculate for the support reactions at A and B.
Q2: For the cantilever beam Shown in Figure 2. Use the data from Table 2. Find the following: I. II. III. The bending moment at B Draw the shear force and bending moment diagrams for the beam The reaction at fixed end Rcy The reaction at the fixed end Mc The shear force at B IV. V. 5kN/m 40 kN A В 2m 2m Figure 2
Q2 Figure shows a structure loaded with vertical load of 40 kN at joint C, horizontal Load of 20 kN at joint C and 30 kN at joint E. The structure is supported by a roller at joint A and pinned at joint F. (а) Determine the determinacy of the structure. (b) Calculate all Reaction Forces at each support. (c) Calculate and sketch the Internal Force due to External Force for each element of the structure. Assume the AE value is coherent or same at all elements and the given value is AE = 80 x 10 kN. Using Method of Virtual Work, fill in the value in the table and determine the following terms, (d) Horizontal displacement of joint C if 1 Unit Load in horizontal direction is applied at the joint. (e) Calculate and sketch the internal force due to the Unit Load at joint C. Vertical displacement of joint D if 1 Unit Load in vertical direction is applied at the joint. (f) (3) Calculate and sketch the internal force due to the Unit Load at joint D. 40KN 20KN B. 3.0m A 30KN 3.0т
Statics and Equilibrium The beam is supported by a fixed support at the left end of the beam. 1. Draw a Free Body Diagram of the beam showing all information. 2. Solve for the reaction forces.
Determine all the support reaction of the given figure A W (KN/m) L b B
a) What is the bar force at CE in KN? b) What is the bar force at CF in KN? c) What is the bar force at DF in KN? Remember: A bar force is a vector quantity so it consists of a magnitude, a unit and a direction.