4. Consider the beam in Fig. 4a, that is similar to the beam shown in Fig. 1a; the beam isloaded with a concentrated moment and a point force as earlier. It is important to take noteof the sense of the applied moment as in the above problem. The cross section of this beam,however, is different and is indicated in Fig. 4b. As in Problem 1, we wish to use the same(a)A(b)Beam crosssection5mBh2m1m8 kN18kN3mсa = 4cm b= 10cmh = 12cmFigure 4: A beam loaded with a concentrated moment and a point force with one end pinned and the othersimply supported. Note the hat shaped but hourglass like cross section of this beam.shear force and bending moment diagrams as in Problem 1 to compute the maximum bendingstress and its location and the shear stress at the neutral axis of this beam's cross section.

A simply supported beam with concentrated moment and a point force of intensity 8 kN with one end…

Answered: shear force and bending moment diagrams…

shear force and bending moment diagrams as in Problem 1 to compute the maximum bending stress and its location and the shear stress at the neutral axis of this beam's cross section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a 4m long statically indeterminate propped cantilever under the loadingconditions shown in Figure for Question. The beam has an I-shapedcross-section. The beam’s E value of 10 GPa and an I value of 218.3×106 mm4 I)Calculate the reaction at B and the equation of the deflected shape. ii)Plot the shear stress distribution across the beam's cross-section at asection immediately right of the prop support at point B. Label keystress values .
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. a. What is the maximum shear of the beam in KN? b. What is the maximum moment of the beam in KN.m? c. What is the distance (in mm) of the neutral x-axis from the indicated x-axis?
Problem A beam of cross-section of an isosceles triangle is subjected to a shear force of 30 kN at a section where base width = 150 mm and height = 450 mm. Determine : (i) horizontal shear stress at the neutral axis, 300 mm C N B FC.G. A 100 mm D
Q3: Determine maximum bending stress in the strut and the orientation of the neutral axis. If the resultant internal moment acting on the cross-section of the aluminum strut has a magnitude of M=510 N.m and is directed as shown. 20 mm B 200 mm 20 mm 20 mm E200 mm 200 mm-
5. The open section of Figure 4 is subjected to an external shear of V in a vertical plane. Locate the shear center of the section. A 3 in B 10 in 0.25 in E 3 in F e 4 in→ Figure 4. Open Steel Section
For the beam shown in the figure, find the shear stress at a point 30 mm above the bottom of the beam at section C.
A beam with the cross-section shown is loaded in such a way that the maximum shear is 4.8 P kN and the maximum moments are 2.5 P kN-m and -3.6 kN+m, where is the applied load in kN. Determine the maximum safe value of P if the allowable shearing stress is 8MPa and the allowable bending stress are 30MPa in tension and 60MPa in compression.
d. What is the location of the absolute maximum shear from the left end of the beam? (in m) e. What is the absolute maximum moment in the beam? (in kNm) f. What is the location of the absolute maximum moment from the left end of the beam? (in m)
This structure is statically indeterminate.There are more reactions than equations.Must use the force method and the redundant forces provided to solve for the axial force, bending moment and shear force diagrams. Flexual rigidity for each part of the structure is provided in the photograph
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the maximum shear of the beam in KN? What is the maximum moment of the beam in KN.m?
Problem (6): Draw the shear and bending diagram for the following structure 4 kN M = 2 KN•M A В C D 2 m – 2 m 2 m
Draw the shear and moment diagram then compute for the maximum value of bending stress. 30 kN 20 kN/m 20 kN/m 3 m 3 m A B C D 1m 1m Section of the beam: 300 mm 400 mm 450 mm E