A displacement sensor has the following specifications: Measurement range ± 10 mm Measurement point 40 mm Resolution 3 µm Linearity 1 % Full Scale Response time 0.15 ms Linear output 4-20 mA. a) State the meaning of each of the terms listed above. b) Calculate the sensitivity of the sensor in mA/mm.

A displacement sensor has the following specifications: Measurement range ± 10 mm Measurement point 40 mm Resolution 3 µm Linearity 1 % Full Scale Response time 0.15 ms Linear output 4-20 mA. a) State the meaning of each of the terms listed above. b) Calculate the sensitivity of the sensor in mA/mm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain the significance of sensors in IoT applications. Provide examples of sensors used in IoT.
name the three different types of spped sensors and describe their respective operation and output.
Draw a brige rectifier circuit with its input and output waveforms. Explain how it works
Cell C O *73% 4G 4G DI 8:04 MTNSA Go Big Go Bozza 1.ll "ll O EID226A Unit 3 The voltage waveforms shown below are obtained from a three-phase power rectifier. Assume a supply frequency of 50HZ. The rectifier output before the inductive filter is denoted by VL and the load voltage after the inductive filter by Vo. VL 100 80 60 40 20 Vo 80 Measure 60 X1 X2 Average Average XI RMS Time 1.60000e-01 2.00000e-01 4.00000e-02 a 40 VL 8.66025e+01 8.66025e+01 -9.63443e-07 8.26991e+01 8.26991e+01 8.40682e+01 Vo 8.17085e+01 8.26722e+01 9.63646e-01 8.17359e+01 8.17359e+01 8.17373e+01 20 0.16 0.17 0.18 0.19 Time (s) Lanere apy diede leo e00 ond sope leod reeietenee of 120 Anglve e the vvovoferme ond epeg:f, Leoleulete
Please answer the questions below: 1. The letters SCR stands for silicon-controlled rectifier. Explain the use of the word rectifier in the name. 2. What two things must happen to cause an SCR to fire or trigger? 3. How much gate current is needed to trigger a medium-power SCR? 4. In words, explain what each of the following symbols stands for: a.) IGt b.) IHO
8. What value of filter capacitor is required to produce 1% ripple factor for a full-wave rectifier having a load resistance of 1.5k2? Assume that the peak value of the output voltage is 18V.
For L load uncontrolled rectifier, draw the grah of the output current and output voltage.
Explain the difference between a digital sensor and an analog sensor. Give an example of each.
Show the Analog Signal Waveform of the problem below. Explain how you got the waveform. The output of the sensor is an analog signal that ranges only from 10 mV to 100 mV and has the highest frequency component of 100 kHz.
RL RECTIFIER OUTPUT Figure 2 1. Referring to Figure 2, a. Explain how to evaluate the correct combination of RL and CL for appropriate filter efficiency. b. Suggest two (2) alternative designs if the output voltage is to be used to drive electronics with various input voltages. Describe how the alternate design can be used.
A semiconductor force sensor has a sensitivity of 0.2 V/lb. If a 3-lb force is applied to the sensor, what would be the sensor voltage?
(i) A single phase half wave controlled rectifier is operated from a 140 V, 50 Hz supply and the load resistance is 5 Q. If the average output voltage is 12.5 % of the maximum possible average output voltage calculate (a) firing Angle (b) average output current (c) draw the output voltage waveform (ii) With neat sketch explain the dynamic turn ON characteristics of the device which is used in high power applications. firing Angle average output current