A digital circuit's input X (X3,.., Xo) represents a four-bit unsigneu mumber from 0 to 6. The output of the circuit: Y = -X For don't cares, the outputs are set to 0's. Use a multiplexer to implement only the most-significant bit (MSB) of the circuit output. From the list below, select the correct set of multiplexer inputs. Draw (on paper) fully-labeled circuit diagram. (Include complete solution the test/exam PDF file). (a) D, 1, 1, D, 0, 0, 0,0 (b) D, D,0, 0, 0, 1,0, 1

A digital circuit's input X (X3,.., Xo) represents a four-bit unsigneu mumber from 0 to 6. The output of the circuit: Y = -X For don't cares, the outputs are set to 0's. Use a multiplexer to implement only the most-significant bit (MSB) of the circuit output. From the list below, select the correct set of multiplexer inputs. Draw (on paper) fully-labeled circuit diagram. (Include complete solution the test/exam PDF file). (a) D, 1, 1, D, 0, 0, 0,0 (b) D, D,0, 0, 0, 1,0, 1

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.3: Signal System

Problem 1R

See similar textbooks

Similar questions

Signal and system plz explain every step that how do this
QUESTION 2 F(A, B, C, D) = Em(0,3,5,8,10,12,13) + Ed (6,7,9,15) a. Implement the above function using a 2-1 multiplexer. Connect signal A to the multiplexer select input. Write expressions for the multiplexer inputs 10 and 1. b. Implement the above function using a 16-1 multiplexer. Write expressions inputs 10 to 15.
To reset IC chips in a system at power-on, the chips must be powered on and working already. That is to say that the reset signal needs to be after the power-on time. Assume that you need to generate a reset signal 1 ms after power-on using an RC circuit, what will be roughly the values of the resistor and capacitor?
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
4. The following Data input and data select waveforms are applied to a Multiplexer. Determine the output waveform. Do D Dy So
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
What is differentiator? For the circuit shown in figure below if input voltage ?? = 3? ? , determine the output voltage ?0 also draw the input & output wave shape.
To implement a Full Subtracter, Using TWO 8:1 Multiplexers (ONE for Sum output and ONE for Cout output). Assign (or Connect) X, Y,and Bin variables to the Select Inputs of Multiplexers and connect 1 or 0 to each Data Input.
Sketch each of the following special digital sequences: a. 58 (n) b. -28 (n-5) c. -5u(n) d. 5u(n-2)
Basic signal system question do it fast
- at A signal Flt) = 2e ult) is applied to the input of.. System have frequency trunsfer funchiom THlw)I = Determine the required relations ibetween the Constants a und b Such that exactly 50% of the input energy on to the output %3D a 1-ohm basis is transffered
What is the value of the 8 digital bits that are represented as in the figure above if (Hint: the first bit is 1): a. The signal is encoded as NRZ-L: b. The signal is encoded as NRZ-I: