a detailed estirntion Per 2000 m le ngt h for the vongete drain 6i4:5) Phol Brtion having the dimensions. 0.15 0.60 m O 60 m m 0.45 m 0.1m 0.75 m-

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: 5. 4

A: Since the question number to be solved is not specified, the solution for figure 5 is as follows:…

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: 40 fé = 3000psi %3D ダク 26" 14 14 fy = 6o ksi %3D 8#8 12 NWC PMa = ?

A: A beam with T section is given in the above question. The value of fc' and fy is provided. also the…

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: Problem 3: A bracket of negligible weight shown in the figure below is loaded a force of 13.34 kN.…

A:

Q: 80 mm -L- В D 60 mm

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: show the (c)

A:

Q: "hat is the degree of indeterminacy of the given Tucture? a. -1 b. 0 С. 1 d. 2

A:

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Prove that Ox - Oy sin 20 + Ty cos 20 and 『;-の cos 20 - Ty sin 20

A: The plane with maximum and minimum normal stresses is known as the principal plane. The shear stress…

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: For the truss shown, determine the stress in members DC and DG. The area of each member is 800 sq.…

A: Given data: Area of each member is 800 mm2.

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.