A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)? Write two(2) decimal places in your answer. Answer Format: 50.55MW I̟ Rine 20 1 Vs Rload 220 2 Vlond = 458.3 kV %3!

A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)? Write two(2) decimal places in your answer. Answer Format: 50.55MW I̟ Rine 20 1 Vs Rload 220 2 Vlond = 458.3 kV %3!

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28P: For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be...

See similar textbooks

Similar questions

Is it right P that given is it input or output power, more over delta/Y 377V/281V ,2.99A/3.15A what does it mean for these . Also free shaft conditions mean?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
5-A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 75.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.2515 c. 0.6122 d. 0.6511
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
primary lines exist in electrical post, wht is the range of voltage passing thru this part of the post. A. 400 V B. 230 V C. 10 000 V D. 13800V
Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
In a PWM, how do we calculate duty cycle?
Complete the sentence The power factor must be close to will be reduced To insure that losses in the transmission lines
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
By applying Kirchhoff current and voltage law
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
Solve for the branch currents Use Kirchhoff's Law (KCL and KVL)