A cylindrical tank 1m in diameter and 6m high contains 2m of water, 1.50m of oil (specific gravity = 0.8) and air under pressure of 20 KPa. If the 10cm diameter orifice located at the vertical side is 30 cm above the bottom of the tank, find the actual discharge at the orifice if C = 0.95.

Q: solution and diagrams

A:

Q: A schematic of the branched pipes is shown in Figure 3. Unit 1 requires a pump placed in line to…

A:

Q: Orificemeter cpilejaye Two small circular orifice of diameters d₁ and d2, respectively, are placed…

A: Two small circular orifices- Diameters = d1 & d2. Depths of tank h1=25 cm & h2=1 m=100 cm,…

Q: A 14m diameter cyclindrical storage contains 900m³ of oil (SG=0.85, v=2x10-³ m²/s). A 30cm diameter…

A:

Q: A 10m diameter cyclindrical storage contains 800m³ of oil (SG=0.85, v=2x10-³ m²/s). A 40cm diameter…

A: Head loss in Pipe- Head loss in pipe are of two types 1) Major Head Loss- It is the loss which occur…

Q: Water at 70°F passes through 0.75-in-internal diameter copper tubes at a rate of 0.4 lbm/s.…

A:

Q: An closed cylindrical tank 4 m in diameter and 10 m high contains 4 m of oil sg = 0.9. An orifice…

A: The objective of the question is to calculate the time required to discharge all the oil from a…

Q: Determine the discharge in liters/s of a new 1.0 m diameter cast iron pipe if the friction loss is…

A: Diameter, D =  1m Friction loss = 10 kPa Length, L = 100 m Specific gravity, S = 0.912 kinematic…

Q: Two vertical circular cylindrical tanks are connected near the bottom by a short tube having a…

A: t= 15.25 sec

Q: Assume Cc=0.62 and cy=0.98, calculate the discharge through a 120-mm diameter orifice under a head…

A:

Q: 2. From the figure shown, pipe AB is 400m long, 200 mm in diameter and f= 0.003, pipe U is 300 m…

A: PipeLength (L)  mDiameter (d)   mFriction factor…

Q: A pipe carrying oil of specific gravity 0.88 changes in size from 150 mm in diameter at section 1 to…

A:

Q: A closed cylindrical tank 5m high contains 2.5m of water. A 100mm diameter circular orifice is…

A:

Q: A sharp-edged orifice 100 mm in diameter, in the side of tank having a horizontal cross-section 2 m…

A: do = 100mm or 0.1mD = 2m Q1 = 20 L/s or 0.02 m3/s Q2 = 30 L/s or 0.03 m3/s Cd = 0.60 -

Q: Oil (s=0.80) and viscosity (u = 0.098 Pa – sec) flow from a reservoir of surface elevation 100…

A: Please find attached images for solution

Q: An incompressible fluid flows through a horizontal pipe which tapers from a diameter of 2 cm to a…

A:

Q: The diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: Water from a supply having a total head of 100 ft is used in the jet of an ejector,shown in the…

A: I hope this is helpful.

Q: (6a) A siphon is made of a pipe whose inside diameter is 25.4 mm and is used to maintain a constant…

A: Data given Siphon pipe, diameter = 25.4 mm = 0.0254 m Depth of tank = 6.0975 m

Q: The centerline of the standard orifice is 3.2 meters above the ground and 3.5 meters below the…

A:

Q: A rigid pipe has a diameter of 150 mm and a length of 1020 m. The water flowing in the pipe has a…

A:

Q: The acting head H above a thick-walled orifice with diameter 4mm under free discharge situation, as…

A: The velocity of flow at orifice is given by V = (2gH)0.5....... Therefore discharge is given by .. Q…

Q: A circular tank has an 34mm diameter orifice on one of its sides discharging oil with a specific…

A:

Q: Question 4: A. For the system shown in the figure, select the proper pump that has the best…

A: Given, CHW = 150  D = 100 mm

Q: to the end of a 350 mm pipe. The pressure at the base of the nozzle where it joins the pipe is 415…

A: Given:- To find:- Velocity of jet

Q: cylindrical liquids, (s=1.05) respectively. An orifice 100 mm at the bottom with a discharge of…

A:

Q: A 10-cm long horizontal nozzle is connected to a 5 cm diameter hose and converges to a 2 cm…

A: Given data in question  Diameter of nozzle 5 cm End Diameter of hose 2 cm Length if nozzle 10 cm…

Q: (in millimeters) of the hole. 3 cm diameter 1.20 m 9 cm diameter 1 m 0.30 m

A:

Q: Water flows through a turbine as shown in figure, where the pipeline upstream of the turbine has a 2…

A: Let us estimate the power delivered to the turbine in step 2.

Q: Determine the pressure (kPa) of the water in the pipe at B, if the tank is filled with crude oil to…

A: Pressure- pressure is defined as the force applied perpendicular to the surface of objects. Unit of…

Q: A 5-m container having the dimensions 1.2x1.2 m² has a sharp-edge orifice 100mm o located at its…

A: Solution: Given: H = 3 m deep a = π4×1002=7853.9mm2 C = 0.60 g = 9.81 height of the vessel = 5 m…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?