A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure is m. Solve for the magnitude of the horizontal component in kN. Unit wt of water - 9.81 kN/cu.m. LENGTH-9 RADIUS 6.5 ANGLE - 49 RADIUS X No new data to save. Last checked at 11:00 1 ANGLE 1.062.35 O1.201.34 O 1.358.45 O 1.066.38

A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure is m. Solve for the magnitude of the horizontal component in kN. Unit wt of water - 9.81 kN/cu.m. LENGTH-9 RADIUS 6.5 ANGLE - 49 RADIUS X No new data to save. Last checked at 11:00 1 ANGLE 1.062.35 O1.201.34 O 1.358.45 O 1.066.38

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3/64 One of the vertical walls supporting end B of the 200-kg uniform shaft of Sample Problem 3/5 is turned through a 30° angle as shown here. End A is still suppor- ted by the ball-and-socket connection in the horizontal x-y plane. Calculate the magnitudes of the forces P and R exerted on the ball end B of the shaft by the vertical walls C and D, respectively. | D یم с B 6 m 7m PROBLEM 3/64 30° A 2 m
Q.>> A Rectangular channel ( = 0:011) 18 m wide to Carry water at The slope f the channel ds 0.00078 (à) Determine the Cottical velocity fao in mls tlow rate 35m /s: (b) Determine the criti cad. depth of. the Floo in meters Dietormine the Specific cheroy in meter8
2:41 Im 2. From the given coplanar force system which consists of two forces and one couple. Replace the force couple system with force acting at A. Figure: 35° 1 m 100 KN 100 KN y₁ 200 KN 50 KN 25° ||| 300 KN.m X 1.00 5G KB/S 50 اس ار59 a. Determine the resultant force acting at point A. b. Determine the Angle (direction) that the resultant R makes with the x-axis. c. Determine the x and y intercepts of the Resultant Force. d. Determine the resultant couple acting at point A.
Determine the displacements of jaints 2 and 3. - For the frome in Figure 1, using Figure 1, using the matrix gstiffness method. 12m - -Take E = 205 GPA (2) 8m 20KN (21 4 A = 6000mm³² I = 180 x 10 mm + 8m 8KNM OP 16m
wo (a) Obtain the total elongation of a steel bar of cross-sectional Area 1250mm² acted 2. by forces indicated in the diagram below. E=205,000N/mm2 15N- SN 20N.. 40N 15N 1.5m 1.5m 3m 1m
Determine the vertical displacement at point B. Note: Use two (2) decimal places in the final answer. 15KN 6kN/m Bll 2EI El EI 2.0 m 4.0m 2.0 m VD 8.0 m O 113.50/EI 153.50/EI 0149.50/EI none of the above
Consider the same beam (orientation a) in Q1. If b=20 cm and h = 10 cm, and if the beam material has a maximum allowable stress of 100 MPa, then what is the maximum bending moment the beam can be exposed to? b Case (a) OI. 333.33 N.m O II. 20000 N.m III. 33333.33 N.m O IV. 1000 N.m Neutral axis
20KN/m 60KN 4m 4m B 8m 8m Analyze the structure using Slope Deflection Method and draw the shear and moment diagram of the system El-Constant E=70GPA I=800x106mm^ 4
Q-5 The dam in Fig. is a quarter circle 50 m wide into the paper. Determine the horizontal and vertical components of hydrostatic force against the dam and the point CP where the resultant strikes the dam. ! 20 m I P. -0 20 m Water
1. The forces acting on a 1-ft length of a dam are shown. The upward ground reaction varies uniformly from an intensity of pa ( Ib/ ft ) at A to ps ( Ib/ ft ) at B. Determine pa and ps and also the horizontal resistance to sliding H. Ans. pA = 1222.22 Ib/ ft - 7' - W=24000lb P=10000lb 1 60° -F=6000lb 6' PA ps 18'
A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure is m. Solve for the location of the horizontal component above point 1 in m. Unit wt of water = 9.81 kN/cu.m. LENGTH= 8 RADIUS= 10 ANGLE = 52 RADIUS X 1 O 2.10 O 2.63 O 2.55 O2.13 ANGLE
11 A cylindrical caisson having an outside diameter of 9 m floats in sea water with its axis vertical and its lower end submerged 9 m, below the water surface. If its center of gravity is on the vertical axis and is 3.6 m above the bottom. a. Determine the value of ??? b. Find the true metacentric height. c. Find the righting couple when the caisson is tipped through an angle of 8°