A customer's plant has two parallel loads connected to the power utility's distribution lines. The first load consists of 50 kW of heating and is resistive. The second load is a set of motors that operate at 0.86 lagging power factor. The motors' load is 100 kVA. Power is supplied to the plant at 10,000 volts rms. a)Determine the total current flowing from the utility's lines into the plant and the plant's overall power factor. b) find the value of the capacitor that should be added to the circuit to improve the power factor to .99 S₁= 50x1 = 5040⁰ Vrms f= 60 Hz = 10 kV P = 50 kW pf = 1 ||S|= 100 kVA pf=0.86 lagging и

A customer's plant has two parallel loads connected to the power utility's distribution lines. The first load consists of 50 kW of heating and is resistive. The second load is a set of motors that operate at 0.86 lagging power factor. The motors' load is 100 kVA. Power is supplied to the plant at 10,000 volts rms. a)Determine the total current flowing from the utility's lines into the plant and the plant's overall power factor. b) find the value of the capacitor that should be added to the circuit to improve the power factor to .99 S₁= 50x1 = 5040⁰ Vrms f= 60 Hz = 10 kV P = 50 kW pf = 1 ||S|= 100 kVA pf=0.86 lagging и

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question#5 Figure below shows a simple single-phase AC power system with three loads. The voltage source is V = 240 < o°v and the impedances of these three loads are z, = 10 < 30°n Z2 = 10 < 45°0 Z3 = 10 < -90°n z,
Two 50-MVA, 3-phase alternators operate in parallel. The settings of the governors are such that the rise in speed from full-load to no-load is 2 percent in one machine and 3 percent in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 100 MW, what would be the load on each machine when the total load is 60 MW? (Req'd) Draw an appropriate diagram.
A 25 cycle emf has an rms value of 250 volts, is zero and increasing positively when time is zero. Determine: a) time when after having gone through its maximum positive value reaches a value of 220 volts, b) time when after having gone through its maximum negative value reaches a value of -150 volts.
13.a. Eddy-current loss in the stator core can be reduced by usingA. alloys with low resistivity.B. annealed iron laminations.C. silicon alloys of copper.D. thin laminations of steel.13.b. Which one of the following is damaging to many insulating materials used in alternators?A. Eddy currentsB. SaturationC. CoronaD. Hysteresis
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.
OR e) Explain the following protection schemes of alternators. i) Stator inter turn protection. ii) Merz price protection.
EX3 Voltage Sag 400 V network short circuit power is 1000 kVA (reactive). A 10 kW induction motor is connected. The motor takes 6-times nominal current when started (assume inductive current). Calculate the voltage drop as a) per unit value, b) per cent value, c) volts in line voltage, d) volts in phase voltage.
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
Explain the principles of power quality in electrical systems and the factors affecting it, including harmonics and voltage sags.
A single phase 120V AC sourc controls power to a resistve load 20N using integral cycle control. a) Find the output power for both output voltage waveforms shown below. b) The voltage and the current ratings of the switch. c) The duty cycle and the value of TON to produce 0.63KW power. d) The power factor for part (c). Awww TON -TON
Explain the concept of power quality and the impact of voltage sags, harmonics, and other issues on electrical equipment.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D