Compute the power dissipation per diode. If the diode is initially reverse-biased, flip the connection and recompute. 153 R1 ww E1=2021 V R1 =15322 R2=27-22 11 =1005 = 10 A + E1 2021 R3 100 Q ww D1 11 D2 D3 ww

Q: Choose correct option Q21/80 Which register is the slowest one OPTIONS SIPO PIPO SISO PISO

A: While PIPO shift register is the fastest one, the slowest shift register is SISO.

Q: Question 17 On Arduino Uno we can use the ________ command to do pulse width modulation:…

A:

Q: Draw the signal for C, D, and E on the timing diagram below. Initial condition, C=0, D=1, E=1.

A: In the given circuit the output waveform of the JK flipflop and the SR flipflop needs to be obtained…

Q: In which method of fault diagnosis ,the input test signal is applied to each stages individually ? O…

A: The correct answer is dynamic testing.

Q: (b) Another of the blocks in the diagram is labelled sample-and hold. (i) Explain the purpose and…

A: (i) to explain the operation and principle of the sample and hold circuit (ii) the sample period is…

Q: Suppose you have measured a time delay of 70 microseconds between the two cursors below. The signals…

A: In this question We need to determine the angle between both signals in degree.  We know Frequency…

Q: Approximately, what is the percent jitter for the following signal? 0.012 0.005 0.011 0.01 主

A: Jitter is a plot which is used to show the value distribution which are very consolidated. It gives…

Q: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

A: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

Q: Q1\Find the Counting states for this Counter:- IIGH Ko K, CLK

A: Synchronous counter given in question We can write the values of JK variables input Jo=Ko=1…

Q: Series connection of switches would normally create O NOR logic gate O NAND logic gate O AND LOGIC…

A:

Q: In control system, the input signal is generally represented as

A:

Q: The first element in any measuring system is the O variable conversion element signal processing…

A: Measurement of any quantity is the comparison of the measured value with a pre defined standard.…

Q: Q: Draw the Isometric view from the given Orthographic views using suitable scale and properly…

A: In the Isometric View below,  the top left corner drawing is the front view. the top right corner…

Q: (INPUT) 01 01 A B C BCD- to- 7 seg. decoder/ driver a 7- Seg. Display (output) What number will be…

A: In this question We need to determine the number will be display in the screen when input is 0101.…

Q: A BCD counter counts from 0 to 9. How many counters are required to count from 0 to 8912?

A: A decade counter has 10 states and it counts from 0 to 9. Flip flops required for the decade…

Q: The instruction JE is equal to O JNZ O JNG O JZ O JNL non of all

A: An instruction is a set of commands given to computer/microprocessor to perform the operation. Types…

Q: (a) (b) (c) (d) If you will inspect the trend of the following situations, going from left to right…

A:

Q: refers to the difference between the measured value and the true one. Confidence interval…

A:

Q: Differentiate between absolute instruments and secondary instruments

A: Different between absolute instruments and secondary instruments:   Absolute instruments…

Q: Draw the circuit of serial in serial out and parallel in parallel out shift register using gates if…

A:

Q: Enter the correct value (either 1 or 0) in each box; consider each row carefully before deciding on…

A:

Q: Draw and label the block diagram of the instrumentation calibration chain.

A: Instrument calibration- Calibrating an instrument is to ensure that the instrument is working…

Q: Which is correct in case of Computer controlled system?

A: Given Data:There are 4 statements regarding computer-controlled systems.Required Data:Here, we need…

Q: Implement a full adder with two 4 × 1 multiplexers.

A: Implementation of Full adder with two 4:1 Multiplexers is explained below: Multiplexer : Multiplexer…

Q: Q what is clocking block and intial block

A: Final block is executed after $finish. Final block doesn't have delay statement.Module is a block a…

Q: what is the size of decoder for 16 x 4 ROM

A: We know that  DECODER: It is a combinational circuit, which contains N-inputs , 2^N outputs and one…

Q: 6- What is the difference between Software and Hardware interrupts?

A: Difference between Software and Hardware interrupts ?

Q: The percentage of measurements subjected to random errors within the deviation boundaries of 20…

A:

Q: 5) In an astable multivibrator when the capacitor is capacitor is using a 555 timer, the and the…

A: For the above given question we need to define the behaviour of the capacitor.

Q: Kindly assist to check if the new design I made with the insertion of this multiplexer works.

A: According to the question, we need to check the design shown below

Q: Flash type ADC is used in most of the applications . Select one: True False

A: Flash analog to digital converter: It is also known as a parallel analog to digital converter. It is…

Q: What is the accuracy of bellow sensor? O a. ± 1% O b. ± 0.001% O c. ± 0.1% O d. ± 0.01%

A: At high differential pressures the accuracy is around 1.5% of the measuring range.  and At lower…

Q: Which of the following element is used to transmit the measured value from one place to another

A: The element which is used to transmit the measured value from one place to another place is Signal…

Q: The carrier signal is always an analog signal. an analog signal in case of an analog information…

A:

Q: 2- Find and plot the output signal of the system as shown: 4 3.5 2.5 3 2 2.5 1.5 2 1.5 1 0.5 0.5 0.5…

A:

Q: The information signal is always an analog signal. an analog signal in case of an analog carrier…

A: Given : Information signal is  a) always an analog signal  b) an analog signal in case of an analog…

Q: Flash type ADC gives highest conversion rate. Select one: True False

A: Flash type ADC