A cube of side 100 mm is subjected to an axial compressive load of 200 kN. Its lateral strain is prevented by applying uniform pressure but only one fourth of lateral strain could be prevented, then which of the following statements is/are correct? Assume E = 200 MPa and μ = 0.3. A The decrease in length in direction of load after applying pressure is 9.358 x 10-3 mm. B The uniform pressure applied has a value of 8.57 N/mm². с The uniform pressure applied has a value of 2.14 N/mm². D The increase in length in lateral direction after applying pressure is 2.25 x 10-3 mm.

A cube of side 100 mm is subjected to an axial compressive load of 200 kN. Its lateral strain is prevented by applying uniform pressure but only one fourth of lateral strain could be prevented, then which of the following statements is/are correct? Assume E = 200 MPa and μ = 0.3. A The decrease in length in direction of load after applying pressure is 9.358 x 10-3 mm. B The uniform pressure applied has a value of 8.57 N/mm². с The uniform pressure applied has a value of 2.14 N/mm². D The increase in length in lateral direction after applying pressure is 2.25 x 10-3 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 1270 mm, b = 790 mm, c = 1.8 mm, and d = 1 mm. d R Answer: Shear strain yry = i prad.
A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in figure. A B BO Calculate the shear stress on oblique plane at 0 = 45° A 0.625 MPa C 0.31 MPa F D 1.25 MPa
The beam is subjected to a bending moment of M = 17 kN. m. σA = B 200 mm OB = 30 mm 30 mm M 30 mm 30 mm 50 mm 150 mm 150 mm 50 mm Part A Determine the bending stress in the beam at point A. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: Q Tap image to zoom Part B Determine the bending stress in the beam at point B. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER:
A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 111o mm, b = 620 mm, c = 0.8 mm, and d = 0.9 mm. Answer: Shear strain yy = prad.
1) A square cross-section cantilever beam is subjected to a force as shown below. What is the maximum force that can be applied to achieve a safety factor on yielding of 1.2 (use the maximum shear stress failure theory)? T = 8N-m L = 10m C=0.5m P=? Al 2024 Sy=455MPa Kic=26MPa (m)1/2
Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. Take P = 9.25 kN. A 30 mm B 400 mm 45 mm '30 mm' 500 mm The maximum tensile stress is 10 mm MPa, and the maximum compressive stress is MPa.
1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q-5KN/m M=4KNM F=3KN L1=3m L2=1m L3=1m 8t M F JA 10t 2t L1 L2 L3 2t 4t
Calculate the design moment strength Mu for the following section. Take f'c = 40 MPa. Sketch the strain and stress distribution diagrams for each section and try to work out your solutions using equilibrium conditions. Yield stress for N bars is 500 MPa. 75 700 60 1500 T 4N28 450
Consider the following figure. hị h A B (a) Determine the maximum tensile stress o, and maximum compressive stress o, (in MPa) due to the load P acting on the simple beam AB. Data are P = 6.8 kN, L = 3.4 m, d = 1.03 m, b = 80 mm, t = 25 mm, h = 120 mm, and h, = 90 mm. (Use the deformation sign convention.) MPa 0. = MPа (b) Find the value of d (in m) for which tensile and compressive stresses are the largest. What are these stresses (in MPa)? (Use the deformation sign convention.) = p MPa MPa
Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam measured from the bottom of the beam. b. Determine the centroidal moment of inertia. c. Determine the largest value of P if the allowable normal stress in tension is 80 MPa and 140 MPa in compression. 96 mm 12 mm T 12 mm 48 mm 0.25 m 0.5 m 0.15 m
2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa). An applied axial load gradually builds up from zero to a value such that the elongation of the bar is 25 mm. Determine the permanent elongation of the bar. o = 3 oy, of = %3D 0.60y . 0.008 0.010 0.005
20 ksi 40 ksi 60 ksi The differential element above represents the state of plane stress at a point in a steel beam. Which of the following best represents the magnitude of the second principal stress (02) at the point? 76.6 ksi O 63.3 ksi 36.6 ksi 60.0 ksi