A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7cm by 5cm dimension.

A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7cm by 5cm dimension.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

Name.. Q3 Water flows through the constant head setup in the laboratory, as shown in the figure, where two identical dense sand samples A and B are placed-one horizontally and the other vertically. The samples are 50 mm diameter and 100 mm in length. The water levels in the left and right sides are maintained at the levels shown, ensuring constant head throughout the test. The void ratio of the sand is 0.92 and the specific gravity of the grains is 2.69. If 165 g of water was collected in the bucket within 15 minutes, 1. What is the permeability of the soil? 2. What the pore water pressure and vertical effective stress at the mid height of sample B? OH 2 190 100+100 A = (50) 7 9 = 0.95 1963.5 100 mm crosesection מות 190 Datumn 40 mm 100 min Arey B.
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7.89cm radius?
ASAP
For a constant head laboratory permeability test on a fine sand, the following are given: Length of specimen = 250 mm Dia. of specimen = 62.5 mm Head difference = 450 mm Water collected in 2 min. = 484 cu.mm Determine the discharge velocity in mm/sec. 0.0789 mm/sec 0.001315 mm/sec 4.734 mm/sec 0.0438 mm/sec
PROBLEM 2: During a constant-head permeability test on a sand sample, 260 x 10° mm³ of water were collected in 2 minutes. If the sample had a length of 100 mm, a diameter of 40 mm and a maintained head of 200mm. What is its coefficient of permeability? a. 0.769 mm/s b. 0.967 mm/s c. 1.321 mm/s d. 0.862 mm/s
A cylindrical soil sample 50 mm in diameter and 200 mm in height is used as thepermeameter in a falling head permeability test setup. In one minute of observation, thehydraulic head in the 10 mm diameter standpipe through which test water went reducedfrom 900mm to 500 mm. During that time, 1.5 liters of water were collected in the graduate. Calculate the soil sample's permeability coefficient in cm/s.
A CD test was conducted on a sample of dense sand 37 mm in diameter × 77 mm long. The cell pressure was 200 kPa. The results are shown in the table below. Axial displacement (mm) 0 0.3 0.6 1.0 1.3 1.6 1.9 3.2 5.2 6.4 7.1 9.7 12.9 15.5 Axial load (N) 0 128.1 225.9 338.9 451.8 508.3 564.8 604.3 593.0 576.0 564.8 525.2 497.0 480.0 (a) Using the data in the table, plot the Deviatoric stress (y-axis) against axial strain (x-axis) graph. (b) Using the graph from (a), draw the Mohr-circle at the peak (i.e., the maximum deviatoric stress). Determine the principal stresses as well. (c) Provided that the sample is sand, draw a failure envelope on the Mohr circle from (b) and determine the friction angle (p').
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
Problem 4. A sample of sand is tested in a constant head permeameter. The sample diameter is 50 mm and its length is 120 mm. Under an applied head of 60 cm, 113 cm³ flows through the sample in 5 minutes. The Mof the sample is 385 grams. Calculate: a. the Darcy coefficient of permeability (k) b. the discharge velocity (v) c. the seepage velocity (v₁)
In falling head permeability test the initial head was 350 mm and the final head was 50 mm. The cross-sectional area of the burette was 200 mm2. The sample was 50 mm in diameter and 100 mm long. If the test took 8 hours and 45 minutes, what was the coefficient of permeability of the soil in m/s? a.7.15 x 10-7 m/s b.6.29 x 10-7 m/s c.7.89 x 10-7 m/s d.8.78 x 10-7 m/s e.5.69 x 10-7 m/s
A constant head permeameter, 85 mm in diameter containing fine sand sample 450 mm long, allowed water to flow at a rate of 184 mL/min under steady flow conditions. Given the difference in head between two points 240 mm apart was 375 mm, determine the coefficient of permeability in mm/s. When the same sample size is tested in a falling head apparatus using a stand-pipe of 32.5 mm diameter, calculate the time required for the water in the stand-pipe to drop from 1750 mm to 1000 mm above the outflow level.
A glass cylinder 5 cm internal diameter and with a screen at the bottom was used as a falling head permeameter. The thickness of the sample was 10 cm. With the water level in the tube at the start of the test as 50 cm above the tail water, it dropped by 10 cm in one minute, the tail water level remaining unchanged. Calculate the value of k (cm/s) for the sample of the soil.