Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN: 9780133923605
Author: Robert L. Boylestad
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
A conductor has a size of 500 MCM, what will be its size in square m?
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 2 steps with 2 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- I need helpo with this. I need step by step solutions for this and I cant figure it out. Wire to be used in buildings and homes in the United States is standardized according to the AWGsystem (American Wire Gauge). Wires are assigned a gauge number according to their diameter.The scale ranges from gauge 0000 to gauge 36 in 39 steps. The equation for the wire gauge interms of the wire diameter in millimeters is as follows.Answer the following questions with your group.(a) What is the equation for the diameter in millimeters in terms of the wire gauge N?(b) You have two wires, one that has five times the diameter of the other. By how much do thewire gauges differ for the two wires? (Give your answer to the nearest integer.)arrow_forwardAt what temperature will intrinsic silicon become a conductor? Assume that un = 350 cm²/Vs and up = 60 cm²/Vs. The properties of silicon are as follows: B = 1.08 x 1031 K-3 cm-6, k = 8.62 x 10-5 eV/K, and EG = 1.12 eV. Hint: o≥1000(2-cm)-1 for a conductor typing format pleasearrow_forwardDetermine the percentage increase in resistance of a copper conductor drawn such that its diamter decreases to 70% that of the original diameter and its length increases by 38%arrow_forward
- A given wire has a resistance of 17.5 ohms. If its length is 560m, how much length must be cut off from the wire in order to reduce its resistance to 12.5 ohms. assume to cross sectional area of the wire to be constantarrow_forwardQuestion 18 Find the drift velocity vdrift of conduction electrons in a gold wire of diameter 2.98 mm when a current of 0.175 A flows in it. The density of conduction electrons in gold is 5.90 x 1028 m-3. O 15.8 x 10-6 m/s O 17.8 x 106 m/s O 4.32 x 106 m/s O 2.66 x 10° m/sarrow_forwardnichrome ribbon resistor elements each has a resistance of 1 ohm. the element is made from sheet of nichrome alloy, 0.025 cm thick. if the width 9f the ribbon is 0.3 cm , what is the length is required per element? assume specific resistance of nichrome alloy to be 10g micro ohm-cmarrow_forward
- Find the resistance of a circular wire that is 0.5-m long with radius of 1mm and has a resistivity value of 0.03 ohm-meter. 4774.65 ohms 5328.03 ohms 7745.64 ohms 2835.31 ohmsarrow_forwardThe resistivity of a ferric-chromium-aluminum alloy is 51x10° ohm-meter. A sheet of the material is 15 cm long, 6 cm wide and 0.014 cm thick. Determine the resistance between a) opposite ends and b) opposite sides.arrow_forward1. Resistive conductors tend to heat up when current flows through them. The temperature of the conductor typically depends on the amount of current it carries, where a higher current leads to a higher temperature. Additionally, the resistivity of a metallic conductor increases with increasing temperature. Therefore, the resistance of a piece of metal will generally increase if the current in the metal increases. This effect is usually negligible if the temperature of a circuit element does not vary too much during its operation. However, this effect can be significant in circuit elements that experience large temperature variations, like incandescent light bulbs and the heating elements in a toaster. The main component in an incandescent light bulb is a coiled filament of tungsten that is 580 mm long with a diameter of 46 µm. At 20°C, tungsten has a resistivity of 5.25 × 10-8 · m. Its temperature coefficient of resistivity is 0.0045 (Cº)-1, and this remains accurate even at high…arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,