A conducting rod is free to slide on two parallel conducting bars. A resistor is connected to the end of the bar. The conducting bar and the rod have negligible resistance. A constant magnetic field is directed perpendicularly into the page. The power dissipated in the resistor is 64 W. The constant speed of the rod is v=8.00 m/s. Find the magnitude of the applied force that is needed to move the rod with this constant velocity. Give your answer in N. B R

A conducting rod is free to slide on two parallel conducting bars. A resistor is connected to the end of the bar. The conducting bar and the rod have negligible resistance. A constant magnetic field is directed perpendicularly into the page. The power dissipated in the resistor is 64 W. The constant speed of the rod is v=8.00 m/s. Find the magnitude of the applied force that is needed to move the rod with this constant velocity. Give your answer in N. B R

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter20: Induced Voltages And Inductance

Section: Chapter Questions

Problem 65AP: In Figure P20.65 the rolling axle of length 1.50 m is pushed along horizontal rails at a constant...

See similar textbooks

Similar questions

Design a current loop that, when rotated in a uniform magnetic field of strength 0.10 T, will produce an emf =0 sin t. where 0=110V and 0=110V .
A square loop whose sides are 6.0-cm long is made with copper wire of radius 1.0 mm. If a magnetic field perpendicular to the loop is changing at a rate of 5.0 mT/s, what is the current in the loop?
How many turns must be wound on a flat, circular coil of radius 20 cm in order to produce a magnetic field of magnitude 4.0105 T at the center of the coil when the current through it is 0.85 A?
The magnetic field perpendicular to a single sire loop of diameter 10.0 cm decreases fron 0.50 T to zero. The re Is made of copper and has a diameter of 2.0 mm and length 1.0 cm. How much charge moves thrnugh the re while tt field is changing?
How is the percentage change in the strength of the magnetic field across the face of the toroid related to the percentage change in the radial distance from the axis of the toroid?
Sodium ions (Na+) move at 0.851 m/s through a blood-stream in the arm of a person standing near a large magnet. The magnetic field has a strength of 0.254 T and makes an angle of 51.0 with the motion of the sodium ions. The arm contains 100 cm3 of blood with a concentration of 3.00 1020 Na+ ions per cubic centimeter. If no other ions were present in the arm, what would be the magnetic force on the arm?
, (a) At what angle 0 is tlie torque on a current loop 90.0% of maximum? (b) 50.0% of maximum? (c) 10.0% of maximum?
The square armature coil of an alternating current generator has 200 turns and is 20.0 cm on side. When it rotates at 3600 rpm, its peak output voltage is 120 V. (a) Wliat is the frequency' of the output voltage? (b) What is the strength of the magnetic field in which the coil is turning?
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
A single-turn square loop of wire, 2.00 cm on each edge, carries a clockwise current of 0.200 A. The loop is inside a solenoid, with the plane of the loop perpendicular to the magnetic field of the solenoid. The solenoid has 30.0 turns/cm and carries a clockwise current of 15.0 A. Find (a) the force on each side of the loop and (b) the torque acting on the loop.
In Figure P20.65 the rolling axle of length 1.50 m is pushed along horizontal rails at a constant speed v = 3.00 m/s. A resist or R = 0.400 is connected to the rails at points a and b, directly opposite each other. (The wheels make good electrical contact with the rails, so the axle, rails, and R form a closed-loop circuit. The only significant resistance in the circuit is R.) A uniform magnetic field B = 0.800 T is directed vertically downward. (a) Find the induced current I in the resistor. (b) What horizontal force F is required to keep the axle rolling at constant speed? (c) Which end of the resistor, a or b. is at the higher electric potential? (d) Alter the axle rolls past the resistor, does the current in R reverse direction? Explain your answer. Figure P20.65
A proton moving horizontally enters a region where a uniform magnetic field is directed perpendicular to the proton’s velocity as shown in Figure OQ22.4. After the proton enters the field, does it (a) deflect downward, with its speed remaining constant; (b) deflect upward, moving in a semicircular path with constant speed, and exit the field moving to the left; (c) continue to move in the horizontal direction with constant velocity; (d) move in a circular orbit and become trapped by the field; or (e) deflect out of the plane of the paper? Figure OQ22.4