A condenser of capacıtance 50 µF, shunted by a non-inductive resistor of 10 2, is connected in series with a resistor of 50 2 to a 200-V, 50-c/s supply. Calculate (a) the current in the condenser ; (b) the current in the shunted resistance; (c) the total current. 85 [(a) 1-85 A ; (b) 1-18 A ; (c) 2-20 A.]

A condenser of capacıtance 50 µF, shunted by a non-inductive resistor of 10 2, is connected in series with a resistor of 50 2 to a 200-V, 50-c/s supply. Calculate (a) the current in the condenser ; (b) the current in the shunted resistance; (c) the total current. 85 [(a) 1-85 A ; (b) 1-18 A ; (c) 2-20 A.]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A circuit consist of a single diode and resistor which are connected to AC source. The resistance voltage is: O AC voltage with V=Vm/ O DC voltage with V=Vm/√2 O AC voltage + DC offset O only DC voltage with V=2Vm/
1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
Q3 (a) Figure Q3(a) shows the circuit diagram diode as a clamper. (i) Name the type of clamper. Determine the overall output voltage, Vout) of the circuit. Show all the calculations and support your answer with the aid of diagram. (iii) Sketch and label clearly the output voltage in parallel with the input voltage. The input voltage is shown in Figure Q3(b). +с - + Si Vin R = 1kn VOUT Voc= 7V Figure Q3(a) Vin 10 - 10 Figure Q3(b)
The D diode used in the diode circuit shown in the figure is a silicon diode. a. Plot the output voltage of the circuit. b. Describe the working principle for each phase in detail R1 10 kN V out +12 V D R2 100 N Vin-15 sin(wt) R3 220 N
When resistors with higher wattage ratings are required, resistors are generally used to dissipate the excessive heat. a) Variable b) Fixed c) Wirewound d) Preset The diode is considered shorted when both anode and cathode has a) Low resistance b) High resistance c) Different resistance d) None of the above When two resistors are connected in parallel then their overall power rating is a) Increased b) Decreased c) Doubled d) Reduced
Q2 (a) Figure Q2(a) shows a clipper circuit made with a gemanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10N and RL=1 kN. (i) Sketch the full cycle of input voltage, Vin(t) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. R. Vin Si Ge R VOUT Vpc Figure Q2(a)
QUESTION 1 If a multiratio CT having 150:5 CT ratio with 0.104 ohm secondary resistance and the excitation current 0.2 A, I -SA Za1 ohm. a) Find the primary side of the CT and show the details of your work. b) Find the CT error and show the details of your work.
Shown below is a diode circuit. If the input signal Vs = 42 Vp-p and the DC voltage Vdc = 8 V, what is the output voltage (in volts) of the circuit during the positive alteration? No need to show your solution. Just write your numeric answer on the space provided. Round off your answer to 2 decimal places. C1 Si D1 Vo Vs 1.0kn Vdc
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to c 20:5A L VI-DC20V 220V omsh T 0.01 F 0.02 F 0.0167 F None of the above euer
D. , D2 A R2 200 Q 100HZ C1 R1 R3 D4 D3 8 µF 2 kQ 3 kQ D Answer the following questions, since the minimum voltage value to transmit the zener diode in the figure given above is 9V and the power of this Zener diode is 0.3 watts. a) Enter the name of the circuit in the figure. b) What are the diodes/diodes in positive half-loop transmission?