A compression member is 8 m long and is pinned at the top and fixed at the bottom and is braced at midspan about its weak axis (axis with lower value of moment of inertia). The properties of the column section are as follows: Area Moment of Inertia, Ix Moment of Inertia, ly "Which of the following most nearly gives the maximum length of the column so that the proportional limit of 320 MPa will not be exceeded? Select the correct response: 10.79 m 8,129 mm² 178.3 x 106 mm4 18.8 x 10 mm4 16.62 m

A compression member is 8 m long and is pinned at the top and fixed at the bottom and is braced at midspan about its weak axis (axis with lower value of moment of inertia). The properties of the column section are as follows: Area Moment of Inertia, Ix Moment of Inertia, ly "Which of the following most nearly gives the maximum length of the column so that the proportional limit of 320 MPa will not be exceeded? Select the correct response: 10.79 m 8,129 mm² 178.3 x 106 mm4 18.8 x 10 mm4 16.62 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(40 Hiw A Pismatic steel bar ofa Square cross section (loo*lo0)mm is looled by Comressive force P= 1300 kU, the bar has length 2.5 m, Eg=200 G Pa, V=0.3,determine the Shortening d, the increase in the dimensions of cross Section , the change in Volume DV of the bar? loomm Joomm
Q1:If allowable stresses are o, 165MPa, o, 100MPa T= 70MPa determine max. value of W. M 300mm 100mm Im 4m Im pe T 300mm 100mm
Determine the force in each member of the truss loaded as shown below. Indicate whether the members are in tension or compression. Summarize your analysis by filling-up the table shown. 300 kN Summary: 3 m Member Internal Force (KN) B AB E D AE BC 5m 400 kN BE CD CE DE - 3 m-3 m
A compression member 3 m. long consists of two angles L 6 x 4 x 1/2 mm with long legs back to back and strutting 12 mm gusset plates at each end. E = 200000 MPa, Fy = 230 MPa Properties of one angle L 6 x 4 x 1/2 mm x = 7.20 x 106mm4 1 ly = 2.59 x 106 mm4 A = 3060 mm² X = 24.9 mm d = 152 mm b = 102 mm y = 50.3 mm a. Compute the minimum radius of gyration. b. compute the allowable axial stress t = 12.7 mm c. compute the safe axial load capacity of the compression member
Two members, 1 and 2, are subjected to thermal stress. Determine the total deformation of member 1 (in mm). Indicate negative sign if in compression. AT=30°C x =11,7 X10 =17:3X10 L-asm E= 200GPA hollow circle each side: Isomm douter= 150 m L-2,5M %3D E: HO Gla %3D regular hexagon dinner= E0 mm
The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P = 50 kN, determine its vertical movement. STEEL L=3 M A= 300 mm² E= 200 GPa 2m зм P= 50 KN ALUMINUM L=43 A== 1500 mm² E-7067.
A steel bar of rectangular cross-section 50 mm x 60 mm is pinned at one end and fixed at the other end. It is subjected to axial compression. If the proportional limit of the material is 240 MPa then (Take E = 210 x 10³ MPa) A Ratio of minimum MOI and maximum MOI of the section is 0.694. Correct Option Minimum length of the column is 1341.22 mm. Minimum length of the column is 1896.916 mm. Correct Option Slenderness ratio is used as a parameter to differentiate between long and short columns. Correct Option
Assume that the truss is simply supported at joints M and E. Determine the stress at member HI if Pu = 18.375 Kips, the area is 11 in?. Answer your problem with the given unit ksi. Pu Pu Pu Pu Pu Pu Pu * (a 10' - L K J I H G F H (a 10' - R Rv 8@10'=80'
Q1:If allowable stresses are o, 165MPa, o, 100MPa T= 70MPa determine max. value of W. CM 300mm Im 4m Im pe T 100mm 100mm 300mm
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
Consider the column section below. It has eight #9 bars. The material properties are as follows: fr =4,000 psi, f, = 60 ksi, and E. = 29,000 ksi. The cross-sectional area of a #9 bar is 1.0 in.². 8- #9 O 2.5" 44 Axis of bending 20" 20" 15"► 2.5" P M The column is subjected to a factored axial load P = 480 kips. Determine the maximum M₁ that can be resisted by the section.
GUIDED PROBLEM An 8 m long steel column is pinned at the top and fixed at the bottom. The column is provided with lateral support at mid-height about the weak axis. The properties of the column section are as follows: 178.1 x 10 mm ly = 18.8 x 10 mm* A=8129 mm² fy=400 MPa What is the critical effective slenderness ratio? What is the Euler critical load? What is the Euler critical stress? a) Determine the effective lengths: a. About the x-axis: It is pinned at the top and fixed at the bottom. k=_ L =_ Effective length: b. About the y-axis: The lateral support at the mid-height will take effect. There will be two segments. Both have lengths of: One of the segments have the pinned support and the lateral support. It will be treated as pinned ends. Thus, k=. The unbraced length is L= The effective length is: kL= The other segment have the fixed support and the lateral support. It will be treated as fixed- pinned column. Thus, k =. The unbraced length is L= The effective length is: kl= From…