A 3-m span cantilever beam carries a uniformly distributed load of 36 KN/m over its entire length. The beam has a rectangular cross-section with height h twice its width b. The allowable stresses are: flexure stress, fb ≤ 30 MPa and shearing stress, fv < 3 MPa. Determine: The maximum shear force along the length of the beam (in KN).

A 3-m span cantilever beam carries a uniformly distributed load of 36 KN/m over its entire length. The beam has a rectangular cross-section with height h twice its width b. The allowable stresses are: flexure stress, fb ≤ 30 MPa and shearing stress, fv < 3 MPa. Determine: The maximum shear force along the length of the beam (in KN).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to the figure shown below, the hinged support at A is in double-shear connection while the support at B in single shear shear connection. Forces P is applied at C and F is an axial force produced from a member BD connected at B. Given data: x = 1.2 m, y = 1.5 m and z = 1.8 m. ∅ = 20 degrees. If the axial stress of BD is limited to 180 MPa, wherein BD is made of 50-mm square tubing with thickness is one-tenth of its dimension, which of the ff. most nearly gives the shearing stress of the 20- mm dia. pin at A in MPa.
A simply supported wood beam carries a concentrated load of P = 8200 lbs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 5.5 in. and a depth of d = 14 in. At section a-a, which is xa = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point K, which is located yk = 4.5 in. below the centroidal z axis. H y Ун a Ук a B K L2 Answer: TK = i psi
A simply supported beam with spans of LAB = 5 ft and LBC = 15 ft supports loads of w = 5.5 kips/ft and P = 29 kips. The cross-sectional dimensions of the wide-flange shape are bf = 7.0 in., tf = 0.61 in., d = 26.0 in., and tw = 0.45 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam.
6.3 Design the beam below using the operating stresses method If the uniformly spread load is n= 10 20 km section width b = 300mm, permissible stresses 140MPa, c=10MPa = ignore the weight of the beam. W-20 kN/m 4m
100 mm M 60° B 100 mm 50 mm 50 mm 200 mm The beam is subjected to the internal moment of M = 2.6 kN?m Determine the maximum bending stress developed in the beam.
Need help ASAP Determine the max flexural stress in MPa
21. Simply supported beam 8 m length has a 2.000 kg load at the center. The flexural stress is 25,000 kPa. Find the section modulus. A. 6,434.56 in3 B. 1,846.56 in3 C. 79.82 in3 D. 95.78 in3
A simply-supported beam with length, L = 10 m, is carrying a downward uniform load, w = 31 kN/m throughout its length. The cross-section of the beam is shown in the figure with a = 480 mm, b = 24 mm, c = 24 mm, and d = 177 mm. Determine the maximum flexural shear stress in MPa. 19 a tot a fof d *
Current Attempt in Progress A simply supported wood beam carries a concentrated load of P = 9600 Ibs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 6.0 in. and a depth of d = 15 in. At section a-a, which is x, = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point H, which is located yH = 3.5 in. above the centroidal z axis. Ук a L Answer: TH = psi
The steel beam has the cross-sectional area shown. If w = 5.2 kip/ft, determine the absolute maximum bending stress in the beam where: L1= 6 ft; L2 =9 ft; bf = 8.5 in; and tw 0.3 in %3D E L1 L2 L1 - C0.30 in. tw 10 in. :0.30 in.
A 4-m span wooden beam with rectangular section simply supports a uniform distributed loading of w=15.85 in KN/m. One support (roller) is located 1-m from the left end and the other support (hinged) is located at the right end of the span. The allowable bending stress is 9 MPa and the allowable shearing stress is 0.60 MPa. Neglect the beam weight and assume the beam to have a depth to width ratio of 1.50. What is the width of the beam so that it will not exceed the allowable bending stress?
A Universal beam of I shaped cross-section is 203 mm deep, and 133 mm wide and has a steel plate 150 mm by 10 mm thick fastened to each flange. Ix-x for the universal beam is 28.80×10^6 mm^4. a) Determine the total uniformity distributed load which may be carried over a simply supported span of 6 metres if the permissible bending stress is 165 N/mm^2. Neglect the self-weight of the beam. [Ans.: 124.02 KN/m] b) Determine the minimum central length over which the additional plates are required. [Ans.: 4.23m]