A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 232 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 124 mm and a wall thickness of 14 mm. The shaft is subjected to torques TB = 49 kN-m and Tc = 15 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (1). TB B Tc

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 232 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 124 mm and a wall thickness of 14 mm. The shaft is subjected to torques TB = 49 kN-m and Tc = 15 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (1). TB B Tc

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 7 kN and Q=5 kN. Determine the normal stress in the rod at x = 0.4 m. Assume a = 0.5 m and b=0.9 m. a Answer: σ= i B MPa O
3. A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of 600 N m. (Practice at Home) 10 mm - 80 mm 10 mm
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 236 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 120 mm and a wall thickness of 16 mm. The shaft is subjected to torques TB = 44 kN-m and TC = 16 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2).
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip·in. and TB = 34 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
1. Each of the four vertical links has a 8 x 38-mm uniform rectangular cross section and each of the four pins has a 18-mm diameter. a. Determine the maximum value of the average normal stress in the links connecting points B and D b. Determine the maximum value of the average normal stress points C and E. 0.4 m c. Determine the average shear stress in pin 0.25 d. Determine the average shear stress in pin С. 20 kN e. Determine the bearing stress acting between pin C and link CE. f. Determine the bearing stress acting between pin D and link BD.
A compound shaft consists of segment (1), which has a diameter of 1.0 in., and segment (2), which has a diameter of 1.3 in. The shaft is subjected to a tensile axial load of P = 16 kips and torques TA = 14 kip·in. and TB = 32 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 128 mm and a wall thickness of 14 mm. The shaft is subjected to torques TB = 48 kN-m and TC = 17 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (1).
Q1/ Draw the normal stress distribution over the cross section on which the maximum normal stress occurs. El = 80000 MPa., E2=20000 MPa A 10 kN/m M- 20 kN MATERIAL 10 MM B MATERIAL MATERIAL 2 100 MM MATERIAL 2 -2 M- -40 mm Q2/ the beam in Q1 (a) find the spacing required between Nails 1 (b) find the spacing required between Nails 2, shear force per nails is 70 kN. 50 mm 16 mm Nail 1- 10 MM- 140 mm Nail 2 16 mm
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If the shaft is made from a material having an allowable shear stress of Tallow = 70MP , determine the maximum value for P Figure 1 of 1 1m 1m 1 m 30 mm 40 mm
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tsquare/Tcircle of the shear stresses. Given: r = 11 mm, S = 18 mm, and t = 2.53 mm. S
The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 95 lb-ft/ft along its entire length. Using a = 2.0 ft, b = 4.0 ft, and c = 8.5 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle oc at the free end of the shaft. b B C Answers: ksi (a) Tmax i rad (b) Pc = i