A composite cube with 40-mm sides and the properties shown is made with glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to a tensile load of 65 kN in the x direction. Determine (b) the stresses o, ay, and o, E =50 GPa E, = 15.2 GPa E = 15.2 GPa - 0.254 M0.254 V= 0.428 The stresses a, ay, and o, are , and MPa, respectively. (up to 1st decimal place please).

A composite cube with 40-mm sides and the properties shown is made with glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to a tensile load of 65 kN in the x direction. Determine (b) the stresses o, ay, and o, E =50 GPa E, = 15.2 GPa E = 15.2 GPa - 0.254 M0.254 V= 0.428 The stresses a, ay, and o, are , and MPa, respectively. (up to 1st decimal place please).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A mass is set on a sqaure box made of polymer. It deforms as shown in following picture. Calculate the shear strain at point O relative to X and Y axes after deformation. L = 12 m, a = 4 m, b = 1 m. %3D %3D X' Y' L b OX
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is d1 = 1.66 in. and the diameter of rod (2) is d2 = 2.68 in. Determine the normal stresses in rods (1) and (2). Assume P = 17 kips and Q = 29 kips. Use positive for tensile stress and negative for compressive stress.
A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mmhas been designed to withstand a maximum internal pressure of 200 MPa inservice. During operation, the pressure within the cylinder is retained by a freelysliding piston. The steel used in the manufacture has Young’s modulus of 210GNm-2.Note: There is no axial stress generated in the cylinder wall in this application.1. Elastic Stress Distributions in a Single Cylindera) At an operating pressure of 200 MPa, calculate using Lame’s equations theradial and circumferential stresses at the cylinder bore and the outersurface.Graphically present (sketch) the general form of variation of each of thesestresses across the cylinder wall, clearly indicating the calculated values atthe cylinder bore and at the outer surface. b) For the same operating pressure, calculate the maximum shear stressvalues at the cylinder bore and the outer surface.Hint: For axisymmetric problems, there are no shear stresses generated onthe…
A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force maximum allowable P that can be applied to the column if the allowable stresses are 12 kpsi in steel and 1200 psi in concrete. Esteel = 29 Mpsi, Econcrete = 3.6 Mpsi. Answer A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force maximum allowable P that can be applied to the column if the allowable stresses are 12 kpsi in steel and 1200 psi in concrete. Esteel = 29 Mpsi, Econcrete = 3.6 Mpsi. Answer: 560 kips.
A cube of side 40 mm, subjected to 3 mutually perpendicular tensile forces of 9 kN, 5 kN, 5 kN acting along X, Y, Z directions respectively. Find the stresses in each directions and the strain along x direction of the cube. Take Young's Modulus of the material as 210 GPa, Poisson's ratio as 0.3. (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNITS GIVEN IN BRACKET) (i) Stress along X direction (Unit in N/mm2) = 5.625 One possible correct answer is: 5.625 (ii) Stress along Y direction (Unit in N/mm2) = 3.125 One possible correct answer is: 3.125 (iii) Stress along Z direction (Unit in N/mm2) = 3.125 One possible correct answer is: 3.125 (iv) Strain along X direction = 1.785*10^-11
3. A mass of 102kg falls 12mm directly onto the end of a bar 25 mm in diameter and 1.5m long. If E for the material is 207 GPa, find the instantaneous stress produced.
Question 4 A steel rod of 20 mm diameter passes centrally through a copper tube of 50 mm external diameter and 40 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projecting parts of the rod. If the temperature of the assembly is raised by 50°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m? and 100 GN/m? and a for steel and copper as 12x 10-6 per °C and 18 x 10-6 per °C.
A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is heated and shrunk to a steel wheel 800.5 mm in diameter. The modulus of elasticity E = 200 MPa. a. Determine the tensile stress in the tire. b. Determine the compressive pressure between the tire and the wheel. c. Determine the thickness of the tire to resist a pressure of 1.5 MPa if it has an allowable stress of 124 MPa. I need answer ASAP. Thank you!
Question 4 A steel rod of 20 mm diameter passes centrally through a copper tube of 50 mm external diameter and 40 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projecting parts of the rod. If the temperature of the assembly is raised by 50°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m² and 100 GN/m² and a for steel and copper as 12x 10-6 per °C and 18 x 10-6 per °C.