A closed container filled with hot coffee as shown below is in a room whose air and walls are at fixed temperature much lower than the coffee. Identify all heat transfer process that contributes to cooling of the coffee. Draw schematics, make necessary assumptions (black body, thickness, materials and convection coefficient) and find the heat flux and temperature of all points of heat transfer if the temperature of coffee and outside surrounding is at 95°C and 28°C respectively.

A closed container filled with hot coffee as shown below is in a room whose air and walls are at fixed temperature much lower than the coffee. Identify all heat transfer process that contributes to cooling of the coffee. Draw schematics, make necessary assumptions (black body, thickness, materials and convection coefficient) and find the heat flux and temperature of all points of heat transfer if the temperature of coffee and outside surrounding is at 95°C and 28°C respectively.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.30P

See similar textbooks

Similar questions

A 0.6-cm diameter mild steel rod at 38C is suddenly immersed in a liquid at 93C with hc=110W/m2K. Determine the time required for the rod to warm to 88C.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless steel . The temperature of the root, , is . The blade is exposed to a hot gas at , and the heat transfer coefficient is K. Determine the temperature of the blade tip and the rate of heat flow at the root of the blade. Assume that the tip is insulated.
What is the minimum amount of ice at OPC that must be added to the contents of a can of diet cola (340m) to cool it down from 20.5C to 0C Assume that the specific heat and density of the diet colo are the same as for water and that no heat is gained or lost to the surroundings. The latent heat of fusion of ice à 3353/g Specific Heat of water 4.184 J/gK and Density of water is 1 g/mL
A closed container filled with hot coffee as shown below is in a room whose air and walls are at fixed temperature much lower than the coffee. Identify all heat transfer process that contributes to cooling of the coffee. Draw schematics, make necessary assumptions (black body, thickness, materials and convection coefficient) and find the heat flux equation and temperature equation at points of heat transfer. Hot coffee Cover Air space Plastic flask
(a) The heating power generated by the nuclear heating rod and the inner temperature of the metallic cylinder, T2. (b) The temperature liquid X, which is located between the nuclear heating rod and the meatllic cylinder, Tliquid. (c) The temperature at the surface of the heating rod, T1. (d) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (e) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (c) and (d), how much the rate of energy transfer to the salt solution ? (f) Compare and discuss the difference of heat transfer with and without the matallic cylinder.
A spherhe of aluminium is staying in an air atmosphere . what would be the change in the internal energy of the sphere with respect to the time given: Ti- initial temperature of the aluminium ( homogeneous) Ta- air temperature (constant) k -conduction coefficient of aluminium hinf- convective coefficient air Cp Cv
For a specified heat input and a given volume which material will have the smallest tempera- ture rise (Use data book if necessary) (a) steel (b) aluminium (c) water (d) copper. When a hot metal piece is left to cool in air the time rate of cooling of the outer layer will be (a) slower at start and faster near the end (b) faster at start and slower near the end (c) both rates will be the same (d) this will depend on the material. (viii) A thin black plate at temperature T receives radiation from a surface at Temperature T1 and radiates to a surface at T2. If all surfaces are black at steady state (a) (T1 – T) > (T – T2) (b) (T1 – T) < (T – T2) (c) (T1 – T) = (T – T2) (d) can be any one of a, b or c. (ix) The temperature profile (in) a slab initially at a constant temperature and then allowed to cool by convection for a short time will be as shown in Fig : (a) E1.2a (b) E1.2b (c) E1.2c (d) E1.2d. Ti
it is desired to understand the time - temperature behavior of a hot copper sphere. the sphere has a diameter D and Is buried a depth Z below the surface of the dry sand in a very large,very deep sand pit far from the edges of the pit. The initial temperature of the sphere is Ti, and the temperature at the surface of the sand is maintained at "T infinity". the difference between the temperature of the sphere and the surface, T - Tinfinity at any time is a function of the initial Temperature difference, Ti - Tinfinity ; the thermal conductivity of the sand, ks ; the thermal conductivity of the copper kc ; the sphere diameter D ; the depth at which it is buried Z; the elapsed time t, and the density times the specific heat Pcp of the copper. What is the best set of repeating variables for this problem? Find the appropiate functional relationship between these parameters in dimensionless form.
The wall (thickness L) of a furnace, with inside temperature 800° C, is comprised of brick material (thermal conductivity = 0.02 W m-! K-')). Given that the wall thickness is 12 cm, the atmospheric temperature is 0° C, the density and heat capacity of the brick material are 1.9 gm cm-3 and 6.0 J kg~1 K-l respectively, estimate the temperature profile within the brick wall after 2 hours. Solve the partial differential equation ()-~ ƏT ƏT subject to the initial condition T(x,0) = 800 sin ; 2L %3D and boundary conditions at the inner (z = L) and outer (r = 0) walls of T = 0 x =0 at and ƏT I = L at Find the temperature profile at T = 7200 seconds = 2 hours.