F₁70 kN and F2 = 60 kN. A is a pin, and F is a roller. Figure -2 m- 40 kN E 50 KN -2 m- H -2 m D C 1 of 1 1.5 m •F₂ 1.5 m 1.5 m F₁ Determine the force in member EH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FEH = Value Submit HÅ Provide Feedback Request Answer Units ? Next

F₁70 kN and F2 = 60 kN. A is a pin, and F is a roller. Figure -2 m- 40 kN E 50 KN -2 m- H -2 m D C 1 of 1 1.5 m •F₂ 1.5 m 1.5 m F₁ Determine the force in member EH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FEH = Value Submit HÅ Provide Feedback Request Answer Units ? Next

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3 The truss ABC shown in the figure supports a horizontal load P-900 lb and a vertical load P2= 300 lb. Both bars have cross-sectional area A-2.4 in. and are made of steel with E-20 X 10 psi. (a) Determine the strain energy U, of the truss when the load P, acts alone (P2 -0). (b) Determine the strain energy U2 when the load P2 acts alone (P 0). (c) Determine the strain energy Uz when both loads act simultaneously. 30 B P =900 lb P2 300 lb 40 in.
The force (in kN) for the member AB in :the figure below is D d2 B di 6 kN
The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. If P1 = P2 = 4 kN, the force in member (CB) is equal to. %3D A 30° 30° OC E D 3 m 3 m P1 P2 Select one: a. 4.618 kN - Tension b. 8 kN - Compression C. 2 kN - Tension d. 8 kN - Tension
The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its pin support at C. %3D Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm? for rod BD. Use E = 200 GPa for steel. A В 0.75 m 1.5 m > 2 m D
A pin-connected structure is supported as shown in the figure. Bar (1) is made of brass [E = 105 GPa], and bar (2) is made of an aluminum alloy [E = 70 GPa]. Bars (1) and (2) each have cross-sectional areas of 375 mm². Rigid bar ABCD is supported by a pin in a double-shear connection at B. If the allowable shear stress for pin B is 130 MPa, calculate the minimum allowable diameter for the pin at B when P = 107 kN. P A 880 mm D B 720 mm 430 mm (2) (1) 260 mm 400 mm
The cantilevered beam is made from the Z-section having the cross section shown in (Figure 1). Figure 2.25 in. 2 in. B 3 in. HH 0.25 in. 0.25 in. 0.25 in. 1 of 1 P Part A If it supports the two loadings P = 30 lb, determine the bending stress at the wall in the beam at point B. Use My Iz+MzIyz IyIz-12 MzIy+MyIyz IyIz-12/ € ) ₂ + (² - Express your answer in kilopounds per square inch to three significant figures. OB= Submit Provide Feedback V ΑΣΦ ↓↑ vec Request Answer ? ksi
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 619 mm?. For the 41 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places 04 m 0.3 m E 0.4 m 0.2 m
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress is s =10 MPa. 500 N/m 1.5 b В - x m 2 m 2 m Find the reaction forces at B. By = 250 N no reaction at B By = 1000 N = -250 N O By = 750 N A
A two member truss ABC is shown in the figure. The force (in kN) transmitted in member AB is - A 11 0.5 m 17 1pc C 1 m B 10 kN
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in2 for all the members. Determine the deformation sustained by members CG and FG
Determine the force in member FG (assume FG is tension) of the truss shown in the figure below?. Set P = 671 lb. 2P 12h 12 12 12 Answer: