A brine solution is heated from 50°F to 90°F in a one shell pass (hot water)-two tube pass (brine) heat exchanger. The hot water enters at 130°F and exits at 100°F. the water flow rate is 0.6 kg/s, and the overall heat transfer coefficient is U= 180 Btu/h ft²F. What heat exchanger area is required?

A brine solution is heated from 50°F to 90°F in a one shell pass (hot water)-two tube pass (brine) heat exchanger. The hot water enters at 130°F and exits at 100°F. the water flow rate is 0.6 kg/s, and the overall heat transfer coefficient is U= 180 Btu/h ft²F. What heat exchanger area is required?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large…

Q: What will affect the heat transfer rate in heat exchangers?

A: Heat transfer rate in a heat exchanger are affected by a number of factors and they are as follows,…

Q: Question 3 An industrial company recently installed a hot water system operates by hot geothermal…

Q: For phase-free heat transfer and turbulent flow on both sides of a tube-boiler type heat exchanger,…

Q: Consider a water-to-water counterflow heat exchanger with these specifications. Hot water enters at…

A: Given data:- Overall heat transfer coefficient ×Surface area (UA)=2200W/K ∆Tm=32.374 °C To…

Q: An unfinned single-pass cross-flow heat exchanger is being designed with an available surface area…

Q: a) Calculate the log-mean-temperature difference and value of overall heat transfer coefficient from…

A: The LMTD value for a parallel flow heat exchanger can be determined as,

Q: 8. A shell and tube heat exchanger (single shell, two tube pass) is used to cool oil from a large…

A: First, we need to calculate the Reynolds number to determine the flow regime. The Reynolds number is…

Q: A two shell, eight tube pass STHE is to heat mineral oil from -5°C to 40°C using water with an inlet…

A: According to the data number if the sell = n = 2 Number of the tube nt = 8 total tubes N=8x2 =16…

Q: QUESTION 8 A concentric-tube, counter-flow heat exchanger, as shown below, is used to cool mercury…

Q: ! Required information Consider a water-to-water counterflow heat exchanger with these…

Q: Saturated water vapor leaves a steam turbine at a flow rate of 1.5 kg/s and a pressure of 0.51 bar.…

A: To find: The required heat exchanger surface area and the water flow rate and for the same water…

Q: How to determine the pressure drop in a shell-and-tube heat exchanger in an industrial piping system…

A: The pressure drop in a shell-and-tube heat exchanger is a crucial parameter in its design and…

Q: A Parallel-Flow concentric tube heat exchanger is used to condense steam at 45°C using cooling water…

Q: An analysis is performed to determine the heat transfer coefficient of a oil-to-water, one-pass…

Q: A shell-and-tube heat exchanger has one shell pass and two tube passes. Oil (cp=2100 J/kg C) heats…

A: GivenCp=2100J/kgCTo1=280oCmo=6kg/sTw1=20oCTw2=85oCmw=8kg/sU=625W/m2C

Q: a) Calculate the log-mean-temperature difference and value of overall heat transfer coefficient from…

Q: l water flowing at 14 kg.s¹ entering at 18 monia with a mass flow rate of 18 kg.s-¹ perature and…

A: mass flow rate of water mw= 14 kg/sec mass flow rate of ammonia ma= 14 kg/sec Hot fluid enter…

Q: Example 2 A shell-and-tube exchanger (two shells, four tube passes) is used to heat 10,000 kg/h of…

Q: Consider operation of a single pass cross-flowheat exchanger with water (cp = 4193 J/kg·K) (mixed)…

A: Given: The specific heat of the water, cw = 4193 J/kg.K The specific heat of the methanol, cm = 2577…

Q: 1. A two shell, eight tube pass STHE is to heat mineral oil from -5°C to 40°C using water with an…

Q: The following represents a parallel heat exchanger which contains 130 tubes each with a diameter of…

Q: Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at…

A: The specific heat of glycerin is .The mass flow rate of glycerin is .The specific heat of ethylene…

Q: At the rate of 5,000 lbm/min, water is heated from 100 to 130-F in a shell-and-tube heat exchanger.…

A: Given: Mass flow rate, m˙1=500 lbm/min, 5000 lbm/min is physically impossible for the given…

Q: gas from a power plant contains noxious vapors that must be condensed by lowering its temperature…

A: Given that , Thi=initial temp of gas =315°C=588KTci=initial temp of water…

Q: At the rate of 5,000 lbm/min, water is heated from 100 to 130-F in a shell-and-tube heat exchanger.…

A: Total heat transfer

Q: Water at the rate of 86 kg/min is heated from 20 to 70-C by an oil having a specific heat of 1.9…

Q: A mathematical expression for the overall heat transfer rate of a cross section exchanger in…

A: Formula Of Cross Flow Heat Exchanger Is Used

Q: What are the common causes of fouling in a heat exchanger? How does fouling affect heat transfer and…

A: The deposition of unwanted materials on the surface of the heat exchanger is known as fouling.

Q: determine the oil mass flowrate

A: here, oil as a minimum fluid is given.so, (m*Cpoil) is minimum. now use NTU relationship with area…

Q: At the rate of 5,000 lbm/min, water is heated from 100 to 130-F in a shell-and-tube heat exchanger.…

A: There is wrong value in the beginning of question, the mass of cold water should be 500 lbm/min.

Q: A Parallel-Flow concentric tube heat exchanger is used to condense steam at 45°C using cooling water…

Q: Required information Consider operation of a single-pass cross-flow heat exchanger with water…

Q: What is the heat exchanger effectiveness

Q: A counterflow, concentric tube heat exchanger is designed to heat water from 34 to 80 deg C using…

Q: Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at…

A: The specific heat of glycerin is .The mass flow rate of glycerin is .The specific heat of ethylene…

Concept explainers

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.

Question

A brine solution is heated from 50°F to 90°F in a one shell pass (hot water)-two tube pass
(brine) heat exchanger. The hot water enters at 130°F and exits at 100°F. the water flow rate is
0.6 kg/s, and the overall heat transfer coefficient is U= 180 Btu/h ft2F. What heat exchanger
area is required?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Heat Exc
A counterflow, concentric tube heat exchanger is designed to heat water from 23 to 80 deg C using hot oil,which is supplied to the annulus at 163 deg C and discharged at 140 deg C. The thin-walled inner tube has a diameter of Di=23 mm and the overall heat transfer coefficient is 500 W/m2. K. The design condition calls for a total heat transfer rate of 3300 W. What is the length of the heat exchanger? Select one: a. 0.49417 b. 1.1269 c. 0.92237 d. 0.6234
Flowing juice like 0.5kg / h enters the parallel-flow heat exchanger at 293 K and is heated by 400K water vapor (Cp = 1.76kJ / kgK), which is 2.5 kg / s. The exit temperature of the juice is 360 K, the area where heat transfer takes place Calculate the efficiency and heat transfer of the heat exchanger if it is 20 m2 and the overall heat transfer coefficient is 280W / m2K. (physical properties of fruit juice will be considered the same as water).
A 2 - shell pass & 4 - tube pass heat exchanger is designed to heat water from 40 C to 90 C flowing inside the tubes at a rate of 7.5 kg/sec while hot gases flowing in the shell at a rate of 10.42 kg/sec with temperature leaving the heat exchanger at 110 C. Consider the specific heat of water and gas of 4.2 kJ/kg K & 1.08 kJ/kg K, respectively. Draw the temp-profile showing the multi-pass effect and determine the temperature of gas entering the heat exchanger.
(1) A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large industrial gas turbine engine. The flow rate of cooling water through the inner tube (Di = 20 mm) is 0.5 kg/s, while the flow rate of oil through the outer tube (Do = 45 mm) is 0.3 kg/s. The oil and water enter at temperatures of 100 and 30°C, respectively. A) What is the main difference between parallel and counter flow heat exchangers? B) How long must the tube be made if the outlet temperature of the oil is 60°C? C) If the heat exchanger is changed to parallel flow heat exchanger, how long must the tube be made if the outlet temperature of the oil is 60°C?
310 m algunaourtsdi bayon bozu (A) In a food processing plant a brine solution is heated from 6°C to 12°C in a double pipe heat exchanger by water entering at 50°C and leaving at 40°C at the rate of 0.166kg/s. If the overall heat transfer coefficient is 850 W/(m².K), what heat exchanger area is required for (1) parallel flow heat exchanger and (2) counter flow heat exchanger. Discuss the results?. Take C₂ (for water)= 4.180 kJ/kg.K mbmeod (isolev si ma do liw novel
In practical applications of heat transfer enhancement techniques, what performance objectives are considered for optimizing the use of heat exchangers?
HERE ARE SOME APPLICATIONS OF SHEEL AND TUBE HEAT EXCHANGER: Power Generation HVAC Marine Applications Pulp and Paper Refrigeration Pharmaceuticals Air Processing and Compressor Cooling Metals and MiningPLEASE MAKE A EXPLANATION FOR THIS
Calculate the liquid flow rate for a heat exchanger with one tube pass. The liquid is heated from 20°C to 93°C by a hot gas at 260°C and 0.45 kg/s. A-4.64 m², U-280 W/m²
20,000 lb/hr of air is to be cooled from 150°f to 100°f by water flowing in a shell-and-tube heat exchanger. cooling water is available at 70°f and should leave the exchanger at 95°f. available to do this cooling assignment is a one-shell pass, two-tube pass exchanged consisting of fifty 1-in OD 18 BWG copper tubes, each 10 ft long. the tubes are arranged inside a 10-in shell on a staggered 1-1/4- inch triangular pitch with baffles spaced every 6 in. is this exchanger satisfactory?
Show that the temperature profile of two fluid streams (hot and cold) that have the same heat capacity rates is parallel to each other at every section of the counter flow heat exchanger.
Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine Cmin and Cmax Find c, e, and NTU Determine heat transfer rate for the heat exchanger. Determine the outlet temperatures of both fluids.