A bolted lap joint is used to connect a rectangular bar to a hanger bracket, as shown in Fig. P2.8-2. If the allowable shear stress in the bolt is 80 MPa, and the diameter of the bolt shank 15 mm, what is the allowable tensile load on the rectangular bar, Pallow., in kN?

A bolted lap joint is used to connect a rectangular bar to a hanger bracket, as shown in Fig. P2.8-2. If the allowable shear stress in the bolt is 80 MPa, and the diameter of the bolt shank 15 mm, what is the allowable tensile load on the rectangular bar, Pallow., in kN?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Three steel plates are joined by three 20-mm diameter rivets. If the ultimate shear stress in the…

Q: 60 b P P 150 100 100 100

Q: 3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same…

Q: A rigid bar AC is supported pinned supported at A and bar DB at B. See typical bolt connection…

A: Given data: L1 = 2.6 m L2 = 2.1 m H = 1.2 m W = 14 kN Shear stress = 40 Mpa To find:- It is asked…

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

Q: For the tension member shown is made of 12 mm x 240 mm plate attached to gusset plate, Fy = 248 MPa,…

A: Tensile strength is defined as the “resistance to lengthwise stress, measured by the greatest load…

Q: As shown in Fig., Six bolts are used in the connection between the axial member and the support. The…

A: To find the diameter of bolt (d)-

Q: 5/8 in- diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the…

A: This question is related to the Bending Stresses from Strength of Material. In this question we…

Q: Determine the force in the most stressed bolt of the group shown in figure (2) using the elastic…

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

A: Force = 22.3 kN or 22300 NDiameter of shank, d = 12 mm Thickness (t) = 8mm

Q: The wall bracket show below carries a load of P Kip. the allowable tensile in the eye bar is 20 ksi,…

A: According to question :

Q: The five-bolt connection shown must support an applied load of P = 400 N. The thickness of the axial…

A: P = 400 kN t = 1 mm b = 16 mm

Q: 1. Calculate the maximum shearing stress developed in the 5 - 16mm diameter bolts. The given 150 KN…

A: Consider the following given figure:

Q: The pin support at A has a double-shear steel bolt as shown. Determine the required diameter of the…

Q: Plate t = 8mm C230x19.9 M20 Bolts Ag = 2,530 mm² d = 229 mm T. %3D tw 5.90 mm 80 %3! by = 61 mm ty =…

Q: The area of the double angle shown is Ag = 5.6 in2. Each angle has a thickness t = 0.25 in. Given U…

A: Double Angle Tension Member Total Gross Area, Ag=5.6 in2 Thickness of angle, t=0.25 in Reduction…

Q: Determine the no. of rivets to fasten the member BD

A: GIVEN: 1. Rivet strengths at working conditions : In Shear = 70 MPa In Bearing = 140 MPa 2.…

Q: Calculate the maximum shearing stress developed in the 5 – 16mm diameter bolts 100 mm 100 mm P=…

Q: Problem No. 1: 200 kN A truss joint is shown in the figure. 2-1. 100x100x12 H (a) Determine the…

A: Given:- A truss joint is shown The magnitude of the load = P = 200 kN The diameter of the bolt is 16…

Q: أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate Fy = 248 MPa Fu =…

Q: Find the bearing stress on a hole, if the thickness of the hole is 400mm, diameter of the hole is…

Q: he bolt is made of a material havin llowable shearing stress of 55.44 M

A: Given:- Allowable tensile stress=140.44MPa Allowable shearing stress=55.44MPa Axial load=17kN…

Q: 1. A tension member is made of 90 mm thick steel plates 225 mm wide by a lap joint made with three…

A: 1.Answer Given data : Thickness of steel plate (t) = 90mm Width of the plate (B) = 225 mm 3 rows…

Q: Five bolts are used in the connection between the axial member and the support. The ultimate shear…

Q: 10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80…

Q: what should be the mini mum For the tigure s how n, dia meter OF the rivets attached as shown TF the…

A: given data allowable axial stress =60MPa allowable shearing stress = 110 MPa width of plate,b =100…

Q: Calculate the tightening torque for an SAE 5, ASTM449, 13UNC grade bolt with a diameter of 1/2 inch.…

A: The application of preload to a fastener by the turning of the fastener's nut. Friction points…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: Consider the free body diagram;

Q: PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter…

A: Data Given:S1 = 40 mmS2 = 80 mmS3 = 100 mmt = 16 mmBolt diameter (db)= 16 mmAsked:Allowable strength…

Q: Calculate the strass In each mamber and identify what the factor of safely to failure 13? 19

A: Given:- Cross section of the members is 3" x 10" To find:- Stress in each members Concept:- Method…

Q: Shear strength value τ = 200 MPa The contents associated with bolts are given. P = 70 kN required…

A: Given, P =70 kNτ = 200 MPa

Q: A bracket shown in the figure 6.9 carries an eccentric load of 30 kN at an eccentricity of 200 mm.…

Q: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

A: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

Q: A structural tee bracket is attached to a column flange with six bolts as shown in Figure . All…

A: Solution

Q: Problem For the frame shown, design the maximum permissible value of P with a factor of safety of…

Q: A double-angle shape is shown in the figure. The steel is A36, and the holes are for…

Q: 2. A butt joint is fastened by four %4" diameter bolts. If the joint transfers a tensile force P of…

A: Objective: To compute the average shearing stress in the bolts and the bearing stress between the…

Q: A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter…

Q: Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by…

A: Shear Stress : Shear stress is the force which causes the deformation of a structure, component or a…

Q: Consider the figure on the right. A steel plate is used to connect a member to a steel column. 5 -…

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Find the required thickness of the bolt head if the thread is 0.25 mm deep.
Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: ✓ Ultimate tensile strength of each member CD is 300 ksi Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in: C and D-2 in E and F - 1 in. 1.5 in. thick Support Plates -2 ft + D 3 ft B 2 in thick Support Mate Solution Step 1. Identify the conditions for design. Stress normal stress in each member CD, OCD shear stress in bolt A, TA shear stress in bolt C, T shear stress in bolt E, T shear stress in bolt F, T bearing stress on member BDE due to: bolt B, BDE-B bolt D, OBDE-D bolt E, OBDE-E bearing stress on support plates at…
The five-bolt connection shown must support an applied load of P = 300 N. The thickness of the axial member: = 1.5 mm. and the width = 18 mm If the ultimate shear stress in the bolts must be limited to 265 MPa with F.O.S = 3.7 . And the ultimate normal stress in the axial member = 250 MPa, with F.O.S = 2.8 , And the ultimate bearing stress in the axial member = 110 MPa, F.O.S = 2.5 Determine the minimum bolt diameter that may be used in the connection
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
3) will upvote anyone who will answer
The beam shown has the following properties. f’c= 30 MPa, fc=13.5 MPa, fy=400 MPa, fs=200MPa. c) The cracked section properties Kd and ICR.
Q.2. The rigid bar AB, atrached to two verti cal rods as shown in Fig (e), is horizontal before the lead p is applied. If the load pe so kN, ditermine its Vertical mmovement. Aluminum Steel A300 mm 200 G A500 mm R-70 GN -3m- Fig (2)
Please correct answer otherwise dislike
Determine the load capacity of the angle LRFD. USE NSCP 2015.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear