A block weighing 100 N is placed on an inclined plane of slope angle 30 degrees and is connected to a second hanging block of weight “W”, by a cord passing over a small frictionless pulley. The coefficient of sliding friction is 0.3. Find the weight “W” for which the 100N block moves up the inclined plane at a constant velocity.

Q: The uniform 20-pound ladder is balanced in the rough floor with ms = 0.8 static friction coefficient…

A: We have to determine the value of horizintal force P that the man needs to apply to the ladder to…

Q: In a road construction. A wedge of weight (W1= 552 N) is used to mobilize the culvert pipe (W2= 1268…

A:

Q: SITUATION 1 The system below is consisting of two solid circular cross-section bars AB and BC,…

A: The length of member ABC  = 1700mm.Diameter of bar BC, ∅BC = 50mmLength of bar BC, LBC =…

Q: The thin-walled single cell beam shown in figure has been idealized into a combination of direct…

A: To determine the location of the shear center for vertical shear loading, we can use the principle…

Q: the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in…

A:

Q: H.W Determine the distance s to which the 90-kg painter can climb without causing the 4-m ladder to…

A: Given:- The mass of the painter = 90 kg The length of the ladder = 4 m  The mass of the ladder = 15…

Q: The gate AB is 4.60 m long and 2.4 m wide perpendicular to the paper and is hinged at A with a stop…

A:

Q: signage is connected to a pole as shown in the figure. if the pole is a hollow shaft with ouside and…

A:

Q: Problem 2 A 7-kg block is released from rest at A and slides down the smooth circular surface from A…

A: Given:- The mass of the block = 7 kg The radius of the smooth circular surface = r = 4 m The angle…

Q: Problem 11: The uniform 7-m steel shaft has a mass of 200 kg and is supported by a ball and socket…

A:

Q: Solve using the yield line method and then find max..W tent M +91 M/2 LL/2-+ L/3- +13-

A: structure in the image:1. Define Node Coordinates and Member Connections:From the image, it appears…

Q: 3. A steel shaft transmits 30kW at 1500rpm. Considering allowable shearing stress of 351.6 kg find…

A:

Q: Problem 1: A structure is made of a horizontal beam AF and a weightless inclined bar CD with pinned…

A: Height of beam at A (h1) = 150mm = 0.15m Height of beam at F (h2) = 250mm = 0.25m Thickness of beam…

Q: A 40 kg block is attached to the wall with a wire and is resting on the 50 kg and 30 kg blocks on an…

A: given mass block of 40kg  resting on 50kg and 30kg blocks   from force balance: N1 = 40gcos30 =…

Q: Describe the Position of lateral pressure resultant for stability analysis.

A: Lateral earth pressure:

Q: Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by…

A:

Q: The 1.4-Mg machine is to be moved over a level surface using a series of rollers for which the…

A: Given data- Weight of the machine W is 1.4 Mg. Coefficient of rolling resistance at ground aa is 0.5…

Q: A platform has mass W that weighs 15000 N is supported by a four equal fixed base column with a…

A:

Q: The motor draws in the cable at C with a constant velocity of Vc = 4 m/s. The motor draws in the…

A: vc=4 m/saD= 3.5 m/sec2VD=0 when , t=0

Q: Problem 1. Determine the minimum horizontal force P required to keep the crate from sliding down the…

A: Given:- The mass of the crate = 50 kg The coefficient of friction between the crate and the incline…

Q: Q5-A) If the shear stress at bottom of the two parallel plates (h=0.3m) is 0.006 N/m². Find the…

A:

Q: b ... oil d water A vertical rectangular plate is submerged half in oil (SG = 0.83) and half in…

A:

Q: Calculate the corresponding depth of neutral axis from the extreme concrete compression fiber in a…

A: Size of beam is given. Tensile steel strain =0.008 concrete compression strain=0.003 We need to find…

Q: a. Determine the ftop at x=8 m from left end. (MPa). b. Determine the fbot at x=8 m from left end…

A:

Q: The coefficient of static friction for both wedge surfaces is 0.49 and that between the 21-kg…

A:

Q: The two 4.6° wedges shown are used to adjust the position of the column under a vertical load F of…

A:

Q: The uniformly loaded isotropically reinforced concrete slab is simply supported at its four- edges,…

A: Solution:- As we know that the moment capacity of slab in yield line theory is, Mu=wu×le28    →for…

Q: Given the dimensions in the figure, one end of the beam is simple and the other end is fixed…

A: In this question, we first need to calculate the support reaction using the equilibrium equations…

Q: 4. A ladder leans against a smooth wall at 50° from horizontal. The ladder weighs 200N and its…

A:

Q: If the motor exerts a constant force of 300 N on the cable, determine the speed of the 20-kg crate…

A:

Q: Calculate the super elevation ё for a railroad track having a rail guage of 1560 mm for a 600 meter…

A:

Q: Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by…

A: As per bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Prob. 4 Consider a slender 2 meter uniform homogeneous 7-kg bar that rests on, and makes 45-degree…

A: For no slipping to occur the bar must be in equilibrium. Draw the FBD showing all forces. Then using…

Q: Using the assigned wide-flange section in the picture having Fy=260 MPa, determine the value of “Pn”…

A: Solution: Given: fy = 260 MPa Span = 30 ft

Q: 4. The 50-kg uniform pole is on the verge of slipping at Av friction at A. 8m 5m

A:

Q: The 187 kg slider at A is held in place on the smooth vertical bar by the cable AB.

A: Solution: The slider is in equilibrium. The smooth bar exerts no vertical forces on the slider.…

Q: 2. If the coefficient of static friction between block A and the incline is us = 0.37, determine WB…

A:

Q: Q3) For the circular arch shown in the figure, compute the value of "P" such that the vertical…

A: