The motor draws in the cable at C with a constant velocity ofVc = 4 m/s. The motor draws in the cable at D with a constantacceleration of ap = 3.5 m/s². vp =0 when t = 0. (Figure 1)FigureB1 of 1Part ADetermine the time needed for block A to rise 3 m.Express your answer to three significant figures and include the appropriate units.t =SubmitPart BμÅValueVA/B =Request AnswerSDetermine the relative velocity of block A with respect to block B when this occurs.Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity isdownward.μAValueSubmit Request Answer?m/s< Return to Assignment Provide Feedback?

vc=4 m/saD= 3.5 m/sec2VD=0 when , t=0

The motor draws in the cable at C with a constant velocity of Vc = 4 m/s. The motor draws in the cable at D with a constant acceleration of ap = 3.5 m/s². vp=0 when t = 0. (Figure 1) Figure < 1 of 1 > ▾ Part A Determine the time needed for block A to rise 3 m. Express your answer to three significant figures and include the appropriate units. t= Value Submit Part B 1 Request Answer S HA VA/B = Value Determine the relative velocity of block A with respect to block B when this occurs. Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity is downward. Submit Request Answer ? → CE ? m/s < Return to Assignment Provide Feedback

The motor draws in the cable at C with a constant velocity of Vc = 4 m/s. The motor draws in the cable at D with a constant acceleration of ap = 3.5 m/s². vp=0 when t = 0. (Figure 1) Figure < 1 of 1 > ▾ Part A Determine the time needed for block A to rise 3 m. Express your answer to three significant figures and include the appropriate units. t= Value Submit Part B 1 Request Answer S HA VA/B = Value Determine the relative velocity of block A with respect to block B when this occurs. Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity is downward. Submit Request Answer ? → CE ? m/s < Return to Assignment Provide Feedback

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QI. Block A has a mass of m kg and is hoisted using the rope-and-pulley system shown. If the collar is moving to the right at V m/s and has acceleration of a m/s at the instant shown, determine the tension in the cable connected to the collar at that instant. c m d m m = 18, v i=9, a = -5, c = 4, d = 9 %3D
igure 1), F = {500i - 300j + 350k} N. Determine the magnitude of the projection of the force F acting along the cable BA. Express your answer to three significant figures and include the appropriate units. 2m Fon BA= Submit B -1m S Value Request Answer 1m μА D 6 m 3m Units ?
2. The figure shows a jam cleat designed for a sailboat where the large friction forces developed by the cams prevent the rope from slipping. Determine the force R supported by each cam bearing from the 900-N rope tension. The coefficient of static friction between the rope and the cams is 0.8. Hint: FBD of one cam only. The line of action of R passes through the point directly above the center of the 80-mm circular cam profile and the center of the cam mounting pin. Ans: R = 1885 N 80 mm. 20 mm 900 N
A 2.5-kg ball (1=2/5 mr²) of radius of 0.5 m is connected to B by cable AB. The ball is falling freely with a velocity of Vc= 2.65 m/s when suddenly cable AB becomes taut. Assume that when the cable becomes taut, end A is directly to the right of the mass center G. B A 1. Which of the following statements is FALSE regarding the ball JUST AFTER the cable becomes taut? a. The ball is in general plane motion. b. The velocity of point A is perpendicular to cable AB c. The tension on the cable is nonzero. d. The velocity of the ball's center of mass is purely vertical 3. Just after the cable becomes taut, which of the following absolute-relative velocity equations is VALID to relate points A and G of the ball? A. U'G=VG ↓ B. 'G = WrGA C.U'G=VA S + wrGA + D. B'G=VA / + COGA! DV 4. The following equations of motion are VALID EXCEPT 8 A Ex: TAB At = mvx B. Ly: mvG - 15 ΧΛΩΔΕ = mucy CEMA: MUGGA = 10 + mvay"GA 8 15 D. 2MG TABAGA = 10-17/ 5. If the impulse exerted by the cable on the ball during…
7:45 O i ersityofcebu.ethinksites.com An indeterminate beam carries concentrated loads as shown in the figure. Using any method you like, solve the following unknowns: Let P = 170N 4P SP ЗР 1m 2m 2m 1m Determine the vertical reaction at point A. (Note: If the reaction is going down put a negative sign, otherwise just don't put any sign) Determine the vertical reaction at point B. (Note: If the reaction is going down put a negative sign, otherwise just don't put any sign) II
Collar C moves with a constant speed v =6 ft/sec along the fixed rod AB where ß =33° and d = 6 ft, as shown. Determine the magnitude of j at the instant when ) = 90°. Give your answer in rad/sec. B A d
00:44 allll PRACTICE QUESTIONS_GET 214-CLASS 1-2-3.pdf 6 A steel bar 300 mm long, 50 mm wide and 12 mm thick is subjected to an axial pull of 84 kN. Find the change in length, width, thickness and volume of the bar. Take E = 200 GN/m? and Poisson's ratio = 0.32. ôt = 0.0027 mm (decrease), ôV = 45.36 mm' (increase)] 7 A rectangular block 250 mm x 100 mm x 80 mm is subjected to axial loads as follows : 480 kN (tensile) in the direction of its length. 900 kN (tensile) on the 250 mm x 80 mm faces. 1000 kN (compressive) on the 250 mm x 100 mm faces. Taking E = 200 GN/m2 and Poisson's ratio as 0.25 find the following : (i) Change in volume of the block. (ii) Values of the modulus of rigidity and bulk modulus for material of the block. A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge length of 200 mm is 0.09 mm and the change in diameter is 0.0039 mm. Cal- culate the Poisson's ratio and the values of the three modulii. 2 of 2
Problem 4. Replace the three forces acting on the plate by a wrench. Specify the magnitude of the force and couple moment for the wrench and the point P (x, y) where the wrench intersects the plate. Xx FB = {-300k} N B Z Fc = {200j} N 5 m FA = {4001} N C 3 m Ans. FR = 539 N; MR = 1.45 kN-m
3/54 The horizontal steel shaft has a mass of 480 kg and is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops un- derneath the shaft. Calculate the tensions T₁ and T₂ in the cables. 1.5 m 1.5 m A x y T₂ 3 m. 1 N B T2 T₁ 4 m. PROBLEM 3/54 1m 3 m
A cable is used as a laundry washing line whose end points are fixed at A and B. The clothes on the line resemble -10 m: В y 5 m 4 m approximately a constant line load w = 72 N/m. Compute the maximal force in the line for a minimal distance of the line to the ground given by 3 m. Select the correct response: 747.94 N 581.73 N 1038.80 N 363.58 N
Refer to the beam shown. 75 kN/m A 2m For the beam shown, what is the value of BBA in terms of El Select the correct response: 5490 kN.m²/El 5220 kN m²/El 1977 kN.m²/El 4m 2860 kN m²/El 90 kN.m 0 60 kNum www Bm D
A circular RCC water tank has an internal diameter of 10 m and has maximum height of water as 4 m. The thickness of wall is 160 mm and the walls of the tank are restrained at the base. IS-code coefficients for moment in cylindrical wall fixed to the base is given below. 2 Coefficient at point DT 0.8H 0.9H +0.0028 -0.0012 10 12 +0.0026 -0.0005 14 +0.0022 -0.0001 1.0H -0.0122 -0.0104 -0.0090 Take unit weight of water as 9810 N/m³ where, H = Height of tank, D = Then moment at the base of wall using the given table is Diameter of tank, T = Thickness of wall