A block A of 10 kg attached to a spring with K=200 N/m is moving downward along the slope. At this position, the spring is un-stretched, and the downward velocsity is 5m/sec. The slope is at an angle of 30 degrees, and force, F is 100 N applied. Find the distance when block A stops.

A block A of 10 kg attached to a spring with K=200 N/m is moving downward along the slope. At this position, the spring is un-stretched, and the downward velocsity is 5m/sec. The slope is at an angle of 30 degrees, and force, F is 100 N applied. Find the distance when block A stops.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.48P: Find the smallest distance d for which the hook will remain at rest when acted on by the force P....

See similar textbooks

Related questions

Q: The rod is attached with ball-and-socket joints to smooth collars A and B at its end points. A is…

A: Given data: The velocity of collar A vA=6.4 fts The angular velocity of the rod is perpendicular to…

Q: The weight of a body is 100 lb. Determine the rate of acceleration (ft/s2) if a net force of 50 lb…

A: Given data:- The weight of a body (m) =100 lb Force applied on the body (F) =50 lb To Find :-…

Q: If the specific gravity of the gasoline is 0.68, determine the pressure at the gasoline-water…

A: Given dataGasolineSg=0.68hw=3fthg=17ftHere using the Standard values

Q: In cars, the coolant cools down the engine and prevents overheating. By absorbing heat from the…

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

Q: 3, A room being air conditioned is being held at 25°C db and 50% RH. A flow rate of 5.m³/s of supply…

Q: ough a throttling valve and a heat exchanger while air flows t are given on the figure. There is no…

A: Given-Information:- The temperature of saturated liquid, T3 = 115°F Mass Flow Rate of the Saturated…

Q: During a viscosity test corresponding to shear stress values of 0,30,55,80,96,110,120 pa the shear…

Q: Problem 3 Determine the support reactions of the simply supported beam loaded as shown below. 5K…

Q: What types of security precautions, for example, apply to vehicle-to-vehicle transfers?

A: When we transfer a vehicle from one location to another location, we need to transport vehicles…

Q: The uniform beam has a mass of 40 kg per meter of length. Determine the reactions at the supports. A…

Q: A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E= 200…

A: GivenE=200GPaσy=236MPay=45mm

Q: An industrial freezer is designed to operate with an internal air temperature of - 20°C when the…

Q: The torque wrench ABC is used to measure the moment or torque applied to a bolt when the bolt is…

A: Given

Q: The uniform beam has a mass of 40 kg per meter of length. Determine the reactions at the supports. A…

Q: Find the work done by the engine cycle shown in the P-V diagram below. P(kPa) 200 100+ a. 3.0 kJ O…

A: Given data P-v diagram of power producing cycle Brief introduction. Work done = area of p-v…

Q: w[N/m] wohn(x)

A: Given

Q: A pump operates at 1992 rpm against a head of 235 m and delivers 0.4 m3/s of water. Determine the…

A: Given Data- N=1992rpm H=235m Q=0.4 m3/s We have to find Specific speed of pump

Q: As shown in the figure, a 260-ft tank contains 25 lb of H₂O initially at 30 lbf/in². The tank is…

Q: 3. The cable and boom shown support a load of 600 kN. Determine the tensile force T in the cable and…

Q: A brass tube with an outside diameter of 20 mm and 4 mm wall thickness is 80 mm long. It is joined…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: An insulated rigid tank is divided into two compartments by a partition. One compartment contains 8…

Q: The man unes the hand truck to move material up the step The truck and contents have a mass of 40 kg…

Q: Calculate the fan power (in kW) if the average pressure drop is 6 In. H2O. Assume the fan Is 70%…

A: Given-Information:- Q = 20000 ft/m3T1 = 77°FP1 = 1 atm To-Determine:- Fan power

Q: A space has occupancy of 35 people engaged in sedentary activity from 8:00 A.M. to 5:00 PM. The…

Q: As shown in the figure, air with a volumetric flow rate of 14,000 ft/min enters an air-handling unit…

Q: A RA P₁ P₂ 2 X₂ X3 x L W0 C X4 B RB Z P₁ = = 30kN; P₂ = 50kN; w= 10kN/m; L = 6m x₁ = 1m; x₂ = 2m; x3…

Q: Draw the V and M diagrams, find the deflection under the 75 klb load and the displacement of point…

A: The free body diagram of member BC is RBH and RBV are the horizontal and vertical resistance force…

Q: 2.2-4 A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard…

A: Given data :- Diameter of cable = 25 mm Weighting P = 38 kn Young's modulus = 140 Gpa Length of…

Q: A furnace wall is made up of three layer of thickness 150 mm, 110 mm, and 125 mm with thermal…

Q: Which of the following is true about machine home, part origin, and tool change position? (choose…

A: Machine tool home is positioned set once by the machine manufacturer hence it makes second…

Q: A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C…

A: GivenF=22lb

Q: 2) The ballistic pendulum is a simple device to measure projectile speed v by observing the maximum…

A: Given data :- Mass of projectile = 40 g Mass of box = 16 kg Maximum angle = 23° Brief introduction:-…

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: 1. ) Question : A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting…

A: Given:Brake power of the pump, BP=35 hpEfficiency of the pump, η=68%Height of discharge, h=60 m

Q: Consider the frame shown in (Figure 1). The suspended cylinder has a mass of 85 kg. Figure 1.5m 2 m…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: In the following cantilevered beam impact configuration pictured in Fig. 1, Determine: 1. The value…

Q: 2.3-10 A two-story building has steel columns AB in the first floor and BC in the second floor, as…

A: Given data:- Load P1 = 400kN Load P2 = 720 kN Young's modulus = 206 Gpa Length L = 3.75m First floor…

Q: The system in the figure is in equilibrium: a) Make 4 free body diagrams b) Calculate Ta(N) and the…

Q: Determine the amount of energy (kJ) that needs to be transferred to the water to raise its…

A: Given:-Mass of water (m) = 55 gallons As 1 gal = 3.79 kg of waterhence Mass of water (m) =…

Q: A pressure relief valve has a pressure setting of 2000 psi. Compute the horsepower loss across this…

Q: Hot combustion gases, modeled as air behaving as an ideal gas, enter a turbine at 145 lbf/in.2,…

A: Given that: At inlet of the turbine, P1 = 145 lbf/in2, T1 = 2700 oR At exit of the turbine, P2 = 29…

Q: A new sports car has a drag corfficient of 0.30 and a frontal area of 18.5 ft<, and is traveling at…

A: Given data. drag coefficient = 0.30 Frontal area = 18.5 ft^2 Speed = 90 mi/h Density = 0.002378…

Q: A closed, rigid tank contains 1.50 kg of water, initially a two phase liquid-vapor mixture at T₁ =…

A: Given data :- mass = 1.50 kg Initial T1=90°C (saturated mixture) And final T2 = 120°C (saturated…

Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…

Q: review the example. Thank you very much Question : Determine the power required (Watts) to drive…

A: Given:Speed of the pump, N=1 rpsDischarge of oil, ρ=850 kg/m3Flow rate, Q=375.3 gpmbore, d=250…

Q: Determine whether the four-bar mechanism is a Crank-Rocker, Rocker-Rocker, Crank-Crank, or…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A: The given information in the problem is represented in the following attached image:

Q: 3. The homogeneous plate of weight 100kN is suspended from two cables. Determine the force that is…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

what happened with the 10 in the first equation?

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
A spring is such that a 5 -lb weight stretches it 6 in. The 5 -lb weight is attached, the spring reaches equilibrium, then the weight is pulled down 3 in. below the equilibrium point and started off with an upward velocity of 6ft/sec. Find an equation giving the position of the weight at all subsequent times
0.8m 0.8m, 1.0m /0.&m 0.6m Title The spring has an unstretched length of 0.4m and a stiffness of 200N/m. The 3 kg slider and attached spring are released from rest at A and move in the vertical plane. (a) Compute the change in elastic potential energy from A to B. (b) Compute the change in gravitational potential energy from A to B. (c) Compute the velocity of the slider as it reaches B in the absence of friction.
The motor exerts a constant force of T (N) on the cable. The final speed of the crate of mass m (kg) is v (m/s). Find the equatlon tidl will define the distance x (m) down the plane that the crate will move, starting from rest. The coefficient of kinetic friction between the plane and the crate is 0.3. The final state is at h = 0 m. 0 (degrees) is the angle between the plane and the horizontal. g = 9.81 m/s?. Crate Motor O !mv /(9.81 * m * sind +T - 0.3 * 9.81 * m * cos0) m O mv / (9.81 * m * sin0 +T+0.3 * 9.81 * m * cos0) m O mv /(-9.81 * m * sin0 – T + 0.3 * 9.81 * m * cos0) m O mv /(9.81 * m* cos0 + T – 0.3 * 9.81 * m* sind) m Clear my choice
8. The toy plane has the three forces shown acting on it and is constrained by the wire to travel in a horizontal circle. The wire has length Wire 55 m and the speed of the plane is 28 m/s. If the mass of the plane is 0.65 kg and 0=18° find the tension in the wire. of airplane lift 0i mg
A spring is stretched 4 inches by a 4 pound weight. The 2 Ib weight is started from the equilibrium position with a downward velocity of 8 ft/s. If air resistance furnishes a retarding force of magnitude 0.02 of the velocity, describe the motion. Find the position of the weight in the first and second stop.
4. A concrete weight of 125 kg is released from standstill and a log of mass 200 kg is moved along an inclined area of 30° to the horizontal.When the concrete weight is moved down 5 m, find that 1. What is the speed of the log? 2. What is the movement time of the concrete drum?
3. For protection, the barrel barrier is placed in front of a bridge pier. The relationship between the force and deflection of the barrier is as given in the plot. For a car weighing 4000 lb and travelling at 50 mph as it first impacts the barrier, find the penetration of the car into the barrier. Note: One interpretation of Up = fF.dr is that work is the area under the force-deflection curve. F (lb) F=90(10)³x¹/2 -x (ft)
Problem 3: Use conservation of energy to find the speed and equations of motion to find the tension. This pendulum is made up of a 20-pound weight at the end of a cord that can be considered weightless. If the pendulum is released from rest from position 1, find its speed and the tension on the cord when it reaches position 2. 1 30° 2 6 ft
1. Parcels are moved via conveyor with velocity vo down to a colinear incline that is static at point A where sliding begins. The parcels eventually fall off at point B, which is 7.0 m past A. If the coefficient of kinetic friction on the incline is 0.40, find the velocity of the conveyor belt, vo, such that the parcels have zero velocity at point B. 7m 15°
In Figure 3, the 1 kg mass hangs from A and attached to a spring at B. The spring constant is k=200 N/m, and the unstretched Jength of the spring is 0.1 m. When the system is released from rest in the position shown in the figure, the spring contracts, pulling the mass to the right. When the string and spring are parallel, determine: b) The tension in the string the 0.3 m 0.15 m datum 0.25 m Figure 3
The two blocks started at rest. The surface of the inclined plane is frictionless. (note: neglect mass and friction of the pulley) Given: Weight of A=230 lb. Weight of B=300 Ib. Calculate: a) acceleration of A (ft/s"), 30° with the horizontal b) Acceleration of B (ft/s"), downward c) the tension in the cable (Ib.) B 30°