A bicycle is placed on a service rack with its wheels hanging free. As part of a bearing test, the front wheel is spun at the rate of N = 46 rev/min. Assume that this rate is constant, and determine the speed v and magnitude a of the acceleration of point A. Assume d = 26 in., 0 = 37% Answers: V= a= ft/sec ft/sec²

A bicycle is placed on a service rack with its wheels hanging free. As part of a bearing test, the front wheel is spun at the rate of N = 46 rev/min. Assume that this rate is constant, and determine the speed v and magnitude a of the acceleration of point A. Assume d = 26 in., 0 = 37% Answers: V= a= ft/sec ft/sec²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

? = 20 degree , Ω = 20 ???/?, dynamics question
For the mechanism in the image below, the end A of the bar is moving downward along the slotted guide with a constant velocity va = 2.1 m/s. If r = 0.5 m, determine the angular velocity W of bar AB when 0 = 38°. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. A A ω, α y В
Determine the velocity of rod R for 0 T/2 rad in the cam C if the cam rotates with a constant angular velocity w = 10 rad/s . The pin connection at O does not cause an interference with the motion of A on C. Enter the velocity of R in m/s in the box below. Assume positive to the left, as shown in the figure. ri = 1 m, r2 = 0.15 m. Enter the answer in m/s in the box below. C www R
2. The gear A on the drive shaft of an outboard motor has a radius of ½ inch while the meshed pinion gear on B has a radius of 1% inches. If the drive starts from rest and is accelerated at a constant a = 200 rad/s², what is the speed, tangential acceleration, and normal acceleration at point P on the propeller after 3 seconds. 2.20 in
Rod OA rotates counterclockwise with a constant angular velocity of 0 = 5 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other slides over the horizontal curved rod, of which the shape is described by the equation = 1.5(2-cos) ft. (Figure 1) Figure r = 1.5 (2 cos 6) ft 6 = 5 rad/s 1 of 1 Part A If both collars weigh 0.60 lb, determine the magnitude of the normal force which the curved rod exerts on one collar at the instant = 140 °. Neglect friction. Express your answer to three significant figures and include the appropriate units. N = Submit μA Value Request Answer Units < Return to Assignment Provide Feedback ?
The rotation of the flywheel is governed by w=2√t where w is in rad/s and t is in sec. θ=3 rad when t=1.5 sec. Find the values of θ and ? when t=3 sec.
9
The disk has an angular acceleration a = 7 rad/s² and angular velocity w = 3 rad/s at the instant shown. It does not slip at A. (Figure 1) Figure y 0.5 m α A 45° C 45° B < 1 of 1 ( Part A Determine the magnitude of the acceleration of point C. Express your answer to three significant figures and include the appropriate units. a = Submit Part B μA 0 = Value Request Answer Determine the direction of the acceleration of point C. Express your answer using three significant figures. 17 Units ΑΣΦ ||1 ? vec Ċ = ? 3 measured counterclockwise from the negative x-axis
In the system on the picture the bigger wheel is not moving, the smaller wheel is connected to the center of the bigger wheel with the rod and it can rotate around the bigger wheel. the smaller wheel starts its movement with angular acceleration ε=10rad/s^2. find the acceleration of point B (marked in a drawing) after 1 full rotation. The radius of the bigger wheel is equal to 0,3m. The radius of the smaller wheel is equal to 0,1m.
The rod AB has a mass of 36 kg and a length of 1.9m. The spring is unstretched when 0- 45°. The spring constant k is 226 N/m. B Find the angular velocity of rod AB at 0 - 0. if the rod is released from rest when 0. 45°. Give your answer with 2 decimals.
Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please write your answer on paper. Thank you so much. Note: The tolerance is ±1 in the third significant digit.
Parvinbhai