A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Taking h=7 mm and using the data given below, determine the largest permissible bending moment when the composite bar is bent about a vertical axis. Brass Aluminum 30 mm 30 mm Aluminum Brass 105 GPa 70 GPa 100 MPa Modulus of elasticity Allowable stress 160 MPa N-m. The largest permissible bending moment is

A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Taking h=7 mm and using the data given below, determine the largest permissible bending moment when the composite bar is bent about a vertical axis. Brass Aluminum 30 mm 30 mm Aluminum Brass 105 GPa 70 GPa 100 MPa Modulus of elasticity Allowable stress 160 MPa N-m. The largest permissible bending moment is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

Question 1.Spiral spring was used to design a mechanical clock. The spring is made of a flat strip 6 mm wide and 0.25 mm thick. The length of the strip is 2.5 m. Assuming the maximum stress of 800 MPa to occur at the point of greatest bending moment. Take E = 200 kN/mm2.(a) Calculate the bending moment.(b) The number of turns to wind up the spring.(c) The strain energy stored in the spring. Question 2A helical compression spring is wound using 2.5 mm diameter music wire. The spring has an outside diameter of 31 mm with plain ground ends, and 14 total coils.a) Estimate the spring rate.b) What force is needed to compress this spring to closure?c) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength?d) Is there a possibility that the spring might buckle in service? Question 3A helical compression spring with square and ground ends has an outside diameter of 14 mm, 20 total coils, a wire diameter of 2 mm,…
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
3. A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn (1 turn = 1.5 mm) given the cross sectional areas and the moduli of elasticity for the steel and the aluminum. AST = 150 mm? EST = 200 GPa EAL = 70 GPa AAL = 100 mm? L=150 mm AST Final 1.5 mm Position Al
For 10 to 12. The compound bar ABCD has a uniform cross-sectional area of 0.25 in². When the axial force P is applied, the length of the bar is reduced by 0.018 in. The moduli of elasticity are 29 x 106 psi for steel and 10 x 10 psi for aluminum. 18 in. 6 in. 18 in. P. P Steel B C Steel D -Aluminum 10. What is p? 11. What is the total elongation of the two steel sections? 12. What is the elongation of the aluminum section?
3. A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength of 240MPA and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross section in mm² of the bar for a factor of safety of 2 is (A) 400 (B) 600 (C) 750 (D) 1000
A bronze bar is fastened between a steel bar and an aluminum bar.Axial loads are applied at the positions indicated and P = 30 kN.Find the total deformation on the composite bar. Assume that theassembly is suitably braced to prevent buckling.Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPaAnswers: δtotal ___________________
Your email address will be recorded when you submit this form. Not eng19mem76@utq.edu.iq? Switch account Q1 The bars AB, CD and EF made of material with E=498 GPa and have a cross sectional area of 587 mm2. The beam ACE is subjected to the force P=174 N. Take L=1.9 m and d=528 mm. Answer the following questions E The force in the bar AB is 112.9695 90.335 96.831
The cross sectional area of the bar is 5cm^2. Use E = 70GPa for aluminum, and E = 200 GPa for steel a. What is the elongation in segment AB (Aluminum)? b. What is the elongation in segment BC (Steel)? c. What is the elongation in segment CD (Aluminum)? d. What is the total elongation of the bar? -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 0.39 in. (Figure 1) Figure 1 in.- 400 lb 800 lb -1.5 in. 1 in. 400 lb Id W₂ a Part A Determine the maximum bending stress on the cross section at the center section a-a. Hint: For the solution it is first necessary to determine the load intensities w₁ and 2. Express your answer in kilopounds per square inch to three significant figures. max = Submit Provide Feedback -- ΑΣΦΑΤΗ1 VO Request Answer vec H ? ksi Next >
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F. Select one: O F= 5712 N O F= 2285 N O F= 8568 N O F= 2856 N O F= 3427 N O F=7140 N Finish attempt..
10/10FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m. R ST = 20 MM
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the stress is not to exceed 130MPa at -20C, find the minimum allowable diameter of the rod. Use a=11.17x10^-6C and E=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong. -Show complete solution and explanation