A ball has a diameter of 28 mm and falls in honey with aterminal velocity of 0.3 m/s. For honey, takePh = 1360 kg/m³ and h = 0.04 m²/s. Note: Thevolume of a sphere is V=³. (Figure 1)Figure1 of 1Part ADetermine the mass of the ball.Express your answer to three significant figures and include the appropriate units.m=SubmitμAValueProvide FeedbackkgPrevious Answers Request Answer?X Incorrect; Try Again; 4 attempts remaining

Given: The diameter of the ball = 28 mm The terminal velocity = 0.3 m/s The density of honey =…

Answered: A ball has a diameter of 28 mm and…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The difference in pressure (in N/m²) across an air bubble of diameter 0.001 m immersed in vater (surface tension = 0.072 N/m): P
Q1/ How does the dynamic viscosity of (a) liquids and (b) gases vary withtemperature? Q2/ What does the friction coefficient represent in flow over a flat plate? How is itrelated to the drag force acting on the plate?
2. Two plates and a fixed surface sandwich two viscous fluid films as shown in the figure. The top plate moves with a velocity of 1.5 m/s and the lower plate is free to move under the influence of the viscous force applied to it. The contact areas for the lower surface of the upper plate is the same as the upper surface of the lower plate as well as the lower surface of lower plate and that of the fixed surface. The density of both fluid is 850 kg/m3. hı=2 mm, hz=1 mm, ui=0.2 Pas. u2=0.5 Pas. (a) After steady state conditions have been reached, what is the velocity of the lower plate? (b) What is the force per unit area imposed on the upper plate to maintain its velocity? Upper plate Viscous fluid 1 Lower plate I h2 Viscous fluid 2 Fixed surface
For the system shown in figure (1), calculate a- The mass flow rate from the nozzle b- The pressure at A and B. Use your last three digits of your ID for height length H_cm H=575 Н сm Water 4 m 150-mm inside diameter 50-mm diameter В At Flow
A 3-kg plastic tank has a volume capacity of 0.2 m^3 and is filled with water. What is the mass of air that the tank can carry? How many tanks can be filled by helium (SG = 0.138) if the total mass of helium is the same with that of air? How many tanks can be filled with oxygen (SG = 1.1044) if the total mass of oxygen is the same with that of air?
Hi, your help is appreciated!
A 1-in diameter cylinder 10 in long falls at 0.6 ft/s inside a tube of slightly larger diameter. A castor-oll film (u=6x10-3 lb-s/ft2) of constant thickness is between the cylinder and the tube. Determine the clearance between the cylinders in the tube in inches. (S.G for steel = 7.85)
Capillary rise of 3 mm is noticed when a glass tube is immersed in a container containing oil of specific gravity 0.64. The contact angle of oil is 190 and surface tension of the oil at 200C in contact with air is 0.088175 N/m. Find the following: (i) Mass density of the oil in kg/m3 (ii) Capillary rise of oil in the glass tube in m of oil
A clean tube has 0.3 cm internal diameter, and it was immersed in a liquid with a surface tension coefficient is 0.48 N/m. The angle of contact of the liquid with the glass is 130°. liquid density is 13.6 g/cm3. What is thelevel of the liquid in the pipe relative to the free surface of the liquid outside the pipe? (g=9.81 m/s2)
An impermeable membrane (See figure above) is placed at the bottom of a U-tube, then equal amounts of water and oil are poured at each limb of the tube such that the height on both sides reads 16.5cm. If the impermeable membrane is removed, calculate the height difference in cm of the U-tube, assuming a uniform cross-sectional area of the U-tube, and given that the specific gravity of oil is 0.843.
A cylinder 1 inch in diameter is placed in a hot water pipe at right angles to the direction of theflow. The fluid and cylinder temperatures are at 80 °F and 100 °F respectively. Calculate thevalue of the film coefficient for a mass flow of 2705 lb/hr.
A thermometer is being designed for a process in which the temperature varies from 0 to 180 °C; from experience it is known that the process temperature, when it gets out of control, reaches up to 240 ° C. Considering that only the bulb is in contact with the part inside the equipment, what should be the volume of the safety vial? It is known that the bulb has a length of 1.2 cm and a diameter of 0.5 cm; the capillary has a length of 20 cm and the scale of the thermometer is -10 to 190 ° C. Consider that the coefficient of volumetric expansion for mercury is 1.82×10−4 ° C− 1

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A ball has a diameter of 28 mm and falls in honey with a terminal velocity of 0.3 m/s. For honey, take Ph = 1360 kg/m³ and V₁ = 0.04 m²/s. Note: The volume of a sphere is V=T³. (Figure 1) Figure < 1 of 1 >