A balanced three-phase three-wire system has a line voltage of 500 V. Two balanced Y-connected loads are present. One is a capacitive load with 7- j2 ohms per phase, and the other is an inductive load with 4 + j2 ohms per phase. a) The magnitude of the phase voltage is V. Do not write units, no decimal places. b) The magnitude of the line current curent is A. Do not write units, round off to one(1) decimal place. c) the total power drawn by the load is kW. Do not write units, no decimal places.

A balanced three-phase three-wire system has a line voltage of 500 V. Two balanced Y-connected loads are present. One is a capacitive load with 7- j2 ohms per phase, and the other is an inductive load with 4 + j2 ohms per phase. a) The magnitude of the phase voltage is V. Do not write units, no decimal places. b) The magnitude of the line current curent is A. Do not write units, round off to one(1) decimal place. c) the total power drawn by the load is kW. Do not write units, no decimal places.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.36P: Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a...

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
Develop the mathematical relationships for the design of the inductance and capacitance of a three-phase double circuit line. A three-phase double circuit line consists of two identical three-phase parallel circuits as shown in the figure below. The circuits are operated with a1-a2, b1-b2, and c1-c2 in parallel.
4. Three-phase circuit
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
THREE-PHASE TRANSFORMERS
In a three-phase system the per-unit phase voltages are 100° , Vôn = 0.8Z180° Van 0.920° , Von = 0.92 - а What are the per-unit symmetrical components V0) and V)? Express in polar notation.
Can you explain the given questions in an original way? Single Phase and Three Phase Principles • Single Phase Generators • Two Phase Generators
Discuss how delta connection is achieved in three-phase systems?
7. Three load units A, B, and Care connected in parallel and take currents that are respectively 11 A, 10A and 15A. Assuming IA to be the reference phasor, IB leads IA by 30degrees and IC legs behind IA by 65degrees. Calculate the total (resultant) currentand angle it makes with the x-axis.