A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced wye connected load. For the system, additional information are as follows: Vca = 212 cis 157 degrees volts; and reactive power per phase is = 433 watts, with 0.7 power factor lagging What is the value of the resistance per phase of the wye load in ohms?

A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced wye connected load. For the system, additional information are as follows: Vca = 212 cis 157 degrees volts; and reactive power per phase is = 433 watts, with 0.7 power factor lagging What is the value of the resistance per phase of the wye load in ohms?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

What is the total real power and total reactive power consumed by the three-phase load (regardless if wye or delta)?
A 500 kVA, 1100 V, 50 hz, wye-connected 3-phasehas armature resistance of 0.1 02/phase and synchronous reactance/phase of 1.502. (i) What is voltage regulation if the load pf is 0.9 lagging ? (ii) what is voltage regulation if the load pf is 0.8 leading?
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
Figure Q2(a) shows a positive sequence three phase circuits. Given a line-to-line voltage at generator, ERY = 415230°V. With assumption that all load impedance are balanced, Zn=Zyb=Zbr= 15 + jl8 2, determine all phase currents at each load and line currents. Include the phasor diagram for all currents in your analysis. R Zry Zyt Figure Q2(a) If the transmission line in three phase circuit at Figure Q2(a) has a impedance of 1+j20 for each phase, determine the phase voltages for each load with using an appropriate analysis. Use phase voltage at generator, ERN as a reference. Then determine the total apparent power, active power and reactive power supplied by the generator.
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
The magnitude of the phase voltage of a balancedthree-phase wye system is 220 V rms. Express eachphase and line voltage in both polar and rectangularcoordinates.
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
What can you say about the flow of power as a function of time between a balanced three-phase source and a balanced load? Is this true of a single-phase source and a load? How is this a potential advantage for the three-phase system? What is another advantage of threephase power distribution compared with single-phase?
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZrY = 50 + j50 N , ZYB = 150 + j0 N and ZBr = 50 –j50 N. jos (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.