a b A jet issues from the side of the tank under a head of a = 4.15 m. The orifice is positioned 5.23 meters above the bottom of the tank. Determine the point it strikes a horizontal plane c = 1.15 m. below the bottom of the tank. Assume the jet will follow a projectile motion. Use e = 42° and Cv = 0.964. Round off to two decimal places.

a b A jet issues from the side of the tank under a head of a = 4.15 m. The orifice is positioned 5.23 meters above the bottom of the tank. Determine the point it strikes a horizontal plane c = 1.15 m. below the bottom of the tank. Assume the jet will follow a projectile motion. Use e = 42° and Cv = 0.964. Round off to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the pressure at point A in the manoter shown. beight b'c = 0.50m
A pipeline system from a water reservoir is designed for filling tank trucks as shown. The 250mm line has an overall length of 30m. The 150mm line is 3m long discharging at A while the one discharging at B is 15m long. Use f=0.03. a. Compute the discharge flowing through the 250mm pipe. b. Compute the discharge flowing through the 150mm pipe at A. c. Compute the discharge flowing through the 150mm pipe at B
Situation 1: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. EI. 240m B El. Om 100mm A O 150mm El. -20m 2. Find the power delivered by the pump in kW. 3. Calculate the pressure head at point 1 in meters. 4. Solve the pressure head at point 2 in meters.
The commercial steel pipe in Figure (3) has a diameter of 3 in. and Figure (3) transfers glycerin from the large tank to the outlet at B. If the tank is open 6 ft at the top, determine the initial discharge at B when the gate valve at C is fully opened. Take, g=32.2ft/s, v=12.8(10)ft/s, KL)Flush entrance elbow=0.9 & KL)Fully opened gate valve-0.19. =0.5, KĻ) 900 2 ft Datum 10 ft
Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in parallel. Q = 10 I/s, V3= 1 m/s, A3 = 0.03 m', CHw=100, d,=150mm, L1 =1500 m, L2 =2000m. di:150 1 V-123 2. 63 21:2000m P: 2.78Td dz?? 74 7.
Q9) A U - tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. The tube is held vertical and partially filled with liquid of surface tension 0.06 N / m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the mass density of the liquid.
Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 T. h.. 2.3m do: 300mn * 2m 454 45 Gm
A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carbon tetrachloride having specific gravity 1.594 under a pressure of 117.72 kPa and pipe B contains oil of sp. gr. 0.8 under a pressure of 117.72 kPa. The pipe lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube.A. 120.58
Air RD -0.75 Q3-A reducer bend having an outlet diameter of 15 cm discharges freely. The bend, connected to a pipe of 20 cm diameter, has a deflection of 667 and lies a horizontal plane. Determine the magnitude and direction of force on the anchor block supporting the pipe when a discharge of 03 m²/s passes through the pipe
The big cylinder can with one closed end is submerged under water with air. The cylinder has dimensions of 5m long and 1m diameter. The columbn of water reached 2m inside the cylinder. Determine how deep in meters was the cylinder submerged from the water surface. Use 101325 Pa as atmospheric pressure. a. 6.84b. 6.80c. 6.88d. 6.90e. 6.82
FRESHMEN What is the value of F required to balance the weight of the cylinder if the weight of the plunger is negligible. Cylinder W= 46kN A= 0.323m² W Oil SG 0.78 ↑ 4.6m ΠΟ F=? Plunger A= 0.00323m²
Provide complete solution. A frustum of a cone is shown, with the orifice at the bottom. C_d=0.62. It contains water at the depth of 3.5m. What is the diameter of the orifice to empty the tank in 8 min. a. 217 mm b. 103 mm c. 100 mm d. 109 mm