A and B are homogeneous with 20 kg and 25 Kg mass respectively. The system is subjected to the force 50 N as shown in the figure. Coefficient of static friction between block A and block B is 0.3 and between block B and the surface is 0.1. Determine whether the two block are in a static condition or moving. 50 N A -0.3 B μ=0.1

A and B are homogeneous with 20 kg and 25 Kg mass respectively. The system is subjected to the force 50 N as shown in the figure. Coefficient of static friction between block A and block B is 0.3 and between block B and the surface is 0.1. Determine whether the two block are in a static condition or moving. 50 N A -0.3 B μ=0.1

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
Two identical wood blocks with weight W are being pushed apart by a wedge. The coefficient of static friction for all surfaces is 0.325. Determine the weight of the wedge, P, required to start the blocks moving. The wedge is symmetrical about the vertical, and 0 = 24°. Use the triangle method or the component method. urgenttt thank you
A horizontal force of P = 100 N is just sufficient to hold the crate from sliding down the plane, and a horizontal force of P = 350 N is required to just push the crate up the plane. Determine the coefficient of static friction between the plane and the crate, and find the mass of the crate. %3D 30°
If A = 1 kg, B = 2 kg, C => 80 Determine the normal force exerted by the horizontal plane to Block B. Find the force F required to start C moving upward. Nb = Blank 1 N F = Blank 2 N Blank 1 Add your answer Blank 2 Add your answer A F 12° H|120 B kg, and the static of coefficient friction is equal to 0.04. C 10°
Two blocks with masses ma = P kg and mg = 100 kg are connected with a flexible cable that passes over a frictionless pulley as shown in Fig. The coefficient of friction between the blocks is 0.2. If motion of the blocks is impending, determine the coefficient of friction between block B and the inclined surface and the tension in the cable between the two %3D blocks. the force for P is 78kg A B 40°
There is a box M₁ with a mass of 20 kg placed on an inclined plane with respect to x-axis of 30°. M₁ is connected with a cable, which is parallel with the inclined plane. The coefficient of the static friction between the surface and the box is μs=0.25. Determine the tension force T in the cable. Assume gravity to be 9.8m/s2. O O 30⁰ T = 98 N T = 55.56 N Don't Know T = 196 N T = 42.44 N M₁ T